Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.
Training layer: use the figure first, then identify the governing rule. All questions are original and aligned to the current Topic 1 boundary.
24 MCQs
5 structured scenarios
29/29 questions with figures
A–D key balance 6/6/6/6
Diagram rule: every figure supplies relevant information or representation. No figure contains the answer or a completed resultant that the question asks you to find.
Paper 1-style MCQ training
Q11.1 Physical quantities
A data logger displays a measurement as 0.024 with no unit. What is required to make the physical quantity complete?
A recorded measurement
Every physical quantity consists of a numerical magnitude and a unit.
Q21.2 SI base units
Which pair consists of two SI base quantities required in this topic?
Quantity cards
Current and thermodynamic temperature are SI base quantities; charge, force, energy, power and pressure are derived.
Q31.1 Estimation
Which is the most reasonable estimate for the wavelength of green visible light?
Scale of a green-light wavelength
Visible light has wavelengths of a few hundred nanometres, i.e. a few ×10⁻⁷ m.
Q41.2 Prefixes
A current is 72 μA. What is the same current in amperes?
Prefix ladder
μ means 10⁻⁶, so 72 μA = 72×10⁻⁶ A = 7.2×10⁻⁵ A.
Q51.2 Prefixes
What is the ratio 1 Gm / 1 μm?
Two prefixes on the same base unit
1 Gm = 10⁹ m and 1 μm = 10⁻⁶ m, so the ratio is 10¹⁵.
Q61.2 Derived units
What is the joule expressed in SI base units?
Work and energy
J = N m = (kg m s⁻²)m = kg m² s⁻².
Q71.2 Derived units
Which pair of quantities has the same SI base units?
Compare derived quantities
Pressure and Young modulus are both measured in Pa = N m⁻² = kg m⁻¹ s⁻².
Q81.2 Derived units
Which expression has the same base units as momentum?
Build a unit from familiar quantities
density×volume gives mass; multiplying by velocity gives kg m s⁻¹, the unit of momentum.
Q91.2 Homogeneity
A model proposes t = √(L/a), where L is length and a is acceleration. What does a unit check show?
Homogeneity check
L/a has units s², so √(L/a) has units s.
Q101.2 Homogeneity
The power available from moving air is modelled by P = kρAvⁿ, where k has no units. What value of n makes the equation homogeneous?
Find the unknown exponent
ρAvⁿ has units kg m^(n−1) s^(−n). Matching kg m² s⁻³ gives n=3.
Q111.3 Errors
A digital balance reads +0.35 g when nothing is on it. What is this?
Balance check
A non-zero reading at zero input is a systematic zero error.
Q121.3 Errors
Repeated measurements of a time are 1.21 s, 1.34 s, 1.27 s, 1.18 s and 1.31 s. The scatter is mainly evidence of what?
Repeated timing results
Unpredictable scatter between repeated readings is characteristic of random error.
Q131.3 Precision and accuracy
The diagrams show two sets of repeated measurements relative to a reference value. Which statement best describes set A?
Repeated measurements around a reference
Set A is tightly grouped (precise) but displaced from the centre/reference (not accurate).
Q141.3 Uncertainty
A = 8.40 ± 0.05 cm and B = 2.10 ± 0.03 cm. For x = A − B, which result uses the correct absolute uncertainty?
Difference of measured quantities
For subtraction, absolute uncertainties add: 0.05+0.03=0.08 cm.
Q151.3 Uncertainty
Q = ab/c. The percentage uncertainties in a, b and c are 2%, 3% and 1%. What percentage uncertainty should be assigned to Q?
Product and quotient uncertainty
For multiplication and division, percentage uncertainties add: 2+3+1=6%.
Q161.3 Uncertainty
A circular area is calculated from A = πr². If r has a percentage uncertainty of 1.5%, what is the percentage uncertainty in A?
Uncertainty in a power
For a power, multiply the percentage uncertainty by the magnitude of the exponent: 2×1.5%=3.0%.
Q171.4 Scalars and vectors
Which pair contains two vector quantities?
Quantity labels
Force and velocity both require magnitude and direction.
Q181.4 Scalars and vectors
A voltmeter may display a negative potential difference. Does the negative sign by itself make potential difference a vector?
Signed reading
A scalar can be positive or negative. Vector character requires transformation/addition by vector rules, not merely a sign.
Q191.4 Vector addition
Two perpendicular forces are 6 N east and 8 N north. What is the magnitude of their resultant?
Two perpendicular forces
For perpendicular vectors, R=√(6²+8²)=10 N.
Q201.4 Vector direction
A force has components 6 N east and 8 N north. What is the direction of the resultant, measured north of east?
Components of one resultant
θ=tan⁻¹(8/6)=53.1°, so about 53° north of east.
Q211.4 Components
A 40 N force acts at 30° above the horizontal. What is its horizontal component?
Resolve this force
The horizontal component is 40 cos30° = 34.6 N.
Q221.4 Vector subtraction
Vector A has components (4, 3) N and vector B has components (1, −2) N. What is |A − B|?
Component form of two vectors
A−B=(3,5) N, so |A−B|=√(3²+5²)=√34=5.83 N.
Q231.4 Equilibrant
Two equal forces act east and north. In which direction must a single balancing force act?
Two equal perpendicular forces
The resultant points north-east, so the balancing force (equilibrant) points exactly opposite: south-west.
Q241.2 Unit equivalence
Potential difference V multiplied by current I gives power. Which SI base-unit expression therefore matches VI?
Unit equivalence
VI has the unit watt; W = J s⁻¹ = kg m² s⁻³.
Paper 2-style structured training
S1Paper 2 style · 12 marks
Sensor package — units, prefixes and homogeneity
Environmental sensor package
A compact sensor package records a current of 3.2 mA, a sampling time of 45 ms and a cable length of 2.4 cm. It also uses the model v = √(F/(ρA)).
(a) Convert the current, time and length to SI units. [3] (b) State the five SI base quantities and units explicitly required in this topic. [5] (c) Use SI base units to show that the expression F/(ρA) has units m² s⁻² and hence that the model is homogeneous for speed. [4]
(a) 3.2×10⁻³ A; 4.5×10⁻² s; 2.4×10⁻² m. [3] (b) mass kg; length m; time s; current A; temperature K. [5] (c) F: kg m s⁻². ρA: (kg m⁻³)(m²)=kg m⁻¹. Therefore F/(ρA)=m² s⁻²; square root gives m s⁻¹, the unit of speed. [4]
S2Paper 2 style · 10 marks
Density calculation with uncertainty
Measured block data
A metal block has the measurements shown. Its density is calculated using ρ = m/(Lwh).
(a) Calculate the density. [3] (b) Calculate the percentage uncertainty in each measured quantity. [3] (c) Determine the percentage uncertainty in ρ. [2] (d) Determine the absolute uncertainty in ρ and quote the final result sensibly. [2]
(a) V=(0.0400)(0.0200)(0.0150)=1.20×10⁻⁵ m³, so ρ=0.0840/(1.20×10⁻⁵)=7.00×10³ kg m⁻³. [3] (b) mass 0.238%; length 0.500%; width 1.00%; height 0.667%. [3] (c) For multiplication/division, percentages add: 2.40% (2.405% before rounding). [2] (d) Δρ≈0.02405×7000≈168 kg m⁻³ ≈ 0.17×10³ kg m⁻³, so ρ ≈ (7.00 ± 0.17)×10³ kg m⁻³. [2]
S3Paper 2 style · 8 marks
Precision, accuracy and error diagnosis
Two instruments measuring a 20.0 unit reference
Two instruments measure a quantity whose independently known reference value is 20.0 units.
(a) Describe the precision of set A and set B. [2] (b) Describe the accuracy of the two sets. [2] (c) Suggest the dominant type of error affecting set A. [1] (d) Explain why simply taking more readings from instrument A would not remove that error. [2] (e) State one appropriate action before further measurements are made. [1]
(a) A is highly precise (small spread); B is less precise (larger spread). [2] (b) A is inaccurate because it is consistently offset; B is accurate overall because its readings are centred near 20.0. [2] (c) A has a systematic error / calibration or zero offset. [1] (d) Repetition reduces the effect of random scatter but does not remove a consistent bias. [2] (e) Check/calibrate the instrument or measure and correct the zero offset. [1]
S4Paper 2 style · 8 marks
Perpendicular forces and equilibrant
Forces acting at one point
Two perpendicular forces of 24 N east and 32 N north act at a point.
(a) Calculate the magnitude of the resultant force. [2] (b) Calculate its direction, measured north of east. [2] (c) State the magnitude and direction of the single force that would balance the two forces. [2] (d) Explain why this balancing force has the same magnitude as the resultant but opposite direction. [2]
(a) R=√(24²+32²)=40 N. [2] (b) θ=tan⁻¹(32/24)=53.1° north of east. [2] (c) 40 N at 53.1° south of west. [2] (d) For equilibrium the vector sum must be zero, so the third force is −R. [2]
S5Paper 2 style · 9 marks
Two-stage displacement
First displacement
A survey aircraft first travels 120 km at 35° north of east, then 50 km due east.
(a) Resolve the first displacement into east and north components. [3] (b) Determine the east and north components of the total displacement. [2] (c) Calculate the magnitude of the total displacement. [2] (d) Calculate its direction north of east. [2]
(a) east=120cos35°=98.3 km; north=120sin35°=68.8 km. [3] (b) total east=148.3 km; total north=68.8 km. [2] (c) magnitude=√(148.3²+68.8²)=163.5 km ≈164 km. [2] (d) θ=tan⁻¹(68.8/148.3)=24.9° north of east. [2]