WONDER — The Mystery
From a Pressure Reading to Actual Motion
A pitot-static instrument compares stagnation and static pressure to infer an ideal flow speed. A measured pressure difference across a panel can then produce a force. Does that force alone describe its acceleration, or must gravity and supports also enter the balance?
Model: Use steady incompressible inviscid Bernoulli conditions for the ideal pitot-static comparison. Use supplied or measured pressure distributions for force calculations. Uniform pressure difference over a horizontal flat area gives ΔPA; nonuniform differences require area-weighted sums or integration. Newton’s laws include gravity, supports and drag when present. Real roofs, wings, spinning balls, vehicles and sprays need their actual flow and pressure fields.
PREDICT — Commit to Your Answer
DOK 2 — PredictA horizontal panel has uniform absolute pressure 100.6 kPa below and 100.2 kPa above. Its area is 0.20 m². Considering only the fluid pressure forces, what is the resultant?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Below-minus-above difference is 0.4 kPa = 400 Pa. The resultant pressure force is 400(0.20) = 80 N upward. Actual acceleration would also require weight and any other forces.
▶ PLAY — Live Pitot-Pressure Panel with a Damped Support
DOK 2 — InvestigatePredict, measure and compare
Compare two flow speeds at fixed panel area and spring stiffness. Then change only panel area from one of that pair. Complete three runs. Watch the airflow markers and the panel move while pressure, spring, damping and gravity obey the stated force balance.
An ideal pitot-static reading uses air density 1.2 kg/m³ and static pressure Ps = 100 kPa. At equal height, stagnation pressure Pt = Ps + ½ρU². A prescribed pressure-regulated chamber applies Pt uniformly below a horizontal panel, with Ps above; this is a defined apparatus model, not a prediction of an arbitrary wing or roof. At t = 0 the chamber’s pressure load is switched on. Fluid pressure regulation and transit are idealized; mechanics use panel mass m = 2.0 kg and g = 9.8 m/s². A bilateral attached linear spring is preloaded to support weight at zero-flow position. Upward displacement x from that position obeys mx″ + cx′ + kx = ΔPA, with critical damping c = 2√(mk). All settings use the same analytical step response. Three physical seconds play over eight real seconds. Panel displacement uses 70 pixels/m, airflow markers use a separate 10 pixels/m strip, and panel width scales with square-root area.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Instruments, Pressure Forces and Real Applications
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Pitot-static speed inference
Click to flip
Pitot-static speed inference
At equal height in the ideal incompressible model, Pt − Ps = ½ρU². The stagnation and static pressures are different readings. Infer U = √[2(Pt − Ps)/ρ] only under suitable flow and instrument conditions.
Rule 2
Integrate the pressure distribution
Click to flip
Integrate the pressure distribution
For a horizontal flat panel, upward pressure force is ∫(Pbelow − Pabove)dA. Uniform difference gives ΔPA. Piecewise uniform patches give a sum of ΔPiAi; an unweighted average is generally wrong.
Rule 3
Include all forces for motion
Click to flip
Include all forces for motion
Fluid pressure force is one term, not automatically the resultant. Add gravity and supports with signs. A positive upward pressure force can coexist with downward acceleration if the other forces dominate.
Rule 4
Lift and momentum are consistent
Click to flip
Lift and momentum are consistent
Wing pressure distributions and airflow momentum change are consistent descriptions of the same aerodynamic force. Equal-transit-time and universal fast-flow slogans are invalid. The flow geometry, angle, pressure field and conditions must be known.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Pressure lift and downward momentum change are separate competing forces to add together.”
Correct — the claim is false.
False. Consistent pressure-field and momentum analyses describe the same aerodynamic interaction. Adding two accounts of the same lift would double-count it.
Myth 2: “Air parcels above and below a wing must reunite at the trailing edge.”
Correct — the claim is false.
False. There is no equal-transit-time requirement. Wing geometry and angle of attack affect the flow; determine its pressure distribution rather than inventing a reunion condition.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Applications with Complete Givens
DOK 2 — ApplyUse actual supplied pressure differences and separate fluid force from resultant force.
Instructor Q1 — Nonuniform Pressures
A flat panel has two patches with different pressure differences and areas. How should their pressure force be found?
Instructor Q2 — Pressure and Momentum
How do complete pressure and momentum accounts of wing lift relate?
Instructor Q3 — Fresh Measured Panel Force
A horizontal panel has uniform below-minus-above pressure difference 500 Pa and area 0.30 m². Find the upward pressure-force magnitude.
Instructor Q4 — Fresh Pitot Reading
An ideal equal-height pitot-static measurement gives Pt − Ps = 240 Pa in air of density 1.2 kg/m³. Neglect compressibility and losses. Find flow speed.
4/4 — Instructor Questions Completed
A defined pressure difference gives a force; a complete force balance gives motion. Measured fields are stronger evidence than a speed-pressure slogan.
✎ PRACTICE — Independent Measurement and Force Applications
DOK 1–3 — PracticeChallenge 1: A Uniform Pressure Panel
A horizontal flat panel has area 0.250 m². Uniform absolute pressure below it is 100800 Pa and above it is 100200 Pa. Find the below-minus-above pressure difference and the upward pressure-force magnitude. Consider only pressure forces.
Step-by-Step Solution
Pressure difference = 100800 − 100200 = 600 Pa. Upward pressure resultant = 600(0.250) = 150 N. The common large absolute part cancels.
Challenge 2: Pitot Speed and Throughput
An ideal pitot-static reading in a uniform filled test section gives stagnation-minus-static pressure 250 Pa. Air density is 1.25 kg/m³ and cross-sectional area is 0.0300 m². Treat the flow as steady, incompressible, inviscid and uniform at the measurement section, with equal measurement heights. Find flow speed, volume flow rate and mass flow rate.
Step-by-Step Solution
Speed = √[2(250)/1.25] = 20.0 m/s. Q = 0.0300(20.0) = 0.600 m³/s. Mass flow = 1.25(0.600) = 0.750 kg/s. These follow the stated ideal instrument and uniform-flow model.
Challenge 3: Audit a Nonuniform Lift Report
A rigid horizontal panel has two patches. Patch 1 has area 1.80 m² and uniform below-minus-above pressure difference +250 Pa. Patch 2 has area 1.20 m² and difference −50.0 Pa. Total panel mass is 50.0 kg; g = 10 m/s². At this instant it is free of supports and other forces besides pressure and gravity. A report takes an unweighted average of the pressure differences, treats pressure lift alone as the total force, and claims the pressures are caused by upper and lower air parcels having to arrive at the trailing edge simultaneously. Find signed upward pressure force, signed upward total force and signed upward acceleration. Explain all three errors.
Step-by-Step Solution
Pressure force upward = 250(1.80) + (−50.0)(1.20) = 450 − 60 = 390 N. The area-weighted average difference is 390/3.00 = 130 Pa, not the unweighted 100 Pa.
Weight = 50.0(10) = 500 N down. Total signed upward force = 390 − 500 = −110 N. Signed upward acceleration = −110/50.0 = −2.20 m/s², downward despite positive pressure lift.
Use an area-weighted pressure distribution, include gravity for the resultant, and reject equal transit time. There is no requirement that air parcels on opposite sides of a wing meet again. Pressure and momentum accounts describe the same interaction; a known pressure field is sufficient for this instantaneous force calculation.
☷ CHALLENGE — Sort Readings, Forces and Motion
DOK 2 — ApplySort Readings, Forces and Motion
Place each statement with the physical step it belongs to.
0 / 6 correct
Physics Insight
The same procedure works from a controlled lab apparatus to a supplied idealized application: evidence, force distribution, full balance.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain how a pitot-static reading can infer speed under suitable conditions, how a pressure distribution gives a force, and why that force alone does not establish acceleration. Explain why pressure and momentum accounts of lift agree and why equal transit time is not required.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 7.12 — Fluid Dynamics Applications
Measure pressure. Sum forces. Respect the flow conditions.
1. Measured pressures first
Static pressure and stagnation pressure are different readings. For an ideal equal-height incompressible comparison, bringing flow to rest gives Pt − Ps = ½ρU². An appropriate pitot-static instrument can use this difference to infer speed. Compressibility, viscous losses, misalignment and nonuniform flow require additional treatment.
2. Pressure distributions give force
For a horizontal flat panel: Fpressure,up = ∫(Pbelow − Pabove)dA
For uniform difference use ΔPA. For piecewise uniform patches sum each signed ΔPiAi. A simple unweighted average only works if the patch areas are equal. Common absolute pressure cancels for equal opposite flat faces. General curved-surface forces require pressure and local normal direction integrated over the surface.
The first practice gives 600 Pa and 150 N upward pressure force. The pitot practice gives speed 20.0 m/s, volume flow 0.600 m³/s and mass flow 0.750 kg/s under the stated conditions.
3. The pressure force is not the whole resultant
Add gravity, support and other stated forces with signs before applying Newton’s second law. Positive upward pressure lift does not alone establish upward acceleration or a climbing flight path.
The two-patch audit gives pressure force 390 N upward, weight 500 N downward, resultant −110 N upward-sign convention and acceleration −2.20 m/s². Its area-weighted average difference is 130 Pa, while the unweighted 100 Pa would give the wrong force.
4. Lift: consistent pressure and momentum descriptions
Integrating a wing’s pressure field gives its aerodynamic force. A consistent control-volume momentum account gives the same interaction through airflow turning. These are compatible descriptions, not extra forces to add. Upper and lower parcels have no equal-transit-time requirement. Geometry, angle of attack and the full flow field matter.
5. Real applications and their limits
Roofs experience spatially varying external and internal pressures; wind speed alone does not determine the sign or magnitude everywhere. This mission supplies measured pressure fields for force exercises and does not model building damage. Nearby vehicles, spinning balls and paper demonstrations can involve unsteady wakes, separation or entrainment that are not captured by one universal speed-pressure rule.
For a liquid riser supplied with a measured pressure deficit at its upper end, the maximum ideal static lift height follows ΔP = ρliquid gh. Creating that deficit and breaking liquid into droplets involve the actual airflow, geometry and losses. Atmospheric pressure can push liquid toward the lower-pressure region; an atomizer is not fully explained by simply labelling all fast air “low pressure.”
6. The live controlled apparatus
The pressure-regulated chamber intentionally applies ideal stagnation pressure below a panel and static pressure above it. Density is 1.2 kg/m³, Ps = 100 kPa and ΔP = ½ρU². This is a defined uniform-pressure apparatus, not a universal model for wings, roofs or vehicle gaps.
Panel mass is 2.0 kg, and an attached bilateral spring is preloaded to balance its 19.6 N weight at the zero-flow position. Let x be upward displacement from that point. Signed upward spring force is W − kx and damping force is −cx′. Thus mx″ = ΔPA + (W − kx) − cx′ − W.
mx″ + cx′ + kx = ΔPA; c = 2√(mk)
The ideal pressure load switches on at t = 0. With x(0) = x′(0) = 0 and ω = √(k/m), the critically damped response is:
x(t) = (ΔPA/k)[1 − (1 + ωt)e^(−ωt)]
Velocity and acceleration are derivatives of this same response; displayed forces satisfy Newton’s law. The bilateral spring can push or pull. Fluid-pressure regulation and transit are idealized, and the mechanical damping dissipates energy, so this is not a lossless free-wing model.
The 3-physical-second observation plays over 8 real seconds. Panel displacement uses 70 pixels/m; the separate airflow strip uses 10 pixels/m. The finite end state is calculated without replacing it by exact equilibrium. Compare speeds, then areas with other controls fixed. Loading earns no credit; three matched completed measurements unlock the next stage.
7. Sources and course scope
Pressure forces apply AP Physics 1 topic 8.2; ideal Bernoulli and throughput applications apply topic 8.4. Cambridge AS Level 9702 pressure concepts support the force calculations, while the Bernoulli instruments and mechanics here are extensions beyond its named fluid requirements.
Concept references: NASA Glenn, Bernoulli and Newton, and Bernoulli’s equation and pitot-static measurement. These optional links are not required for offline use.
✓ Crest’s Checklist
- I distinguish static and stagnation pressure readings.
- I state the ideal instrument assumptions.
- I weight pressure differences by their areas.
- I include gravity and supports in the resultant.
- I read actual motion from the full force balance.
- I avoid double-counting pressure and momentum accounts.
- I reject equal-transit-time and universal speed-pressure claims.
- I distinguish defined apparatus models from real flow fields.
— Crest ☆ “Measure pressure. Sum forces. Respect the flow conditions.”
Mission 7.12 Complete! · All 10 levels cleared · PHYSICS CREST
★ Fluid Dynamics Applications Master
A defined pressure difference gives a force; a complete force balance gives motion. Measured fields are stronger evidence than a speed-pressure slogan.