Skip to lesson
PC

PHYSICS CREST

Global Physics Academy

Mission 7.2 · Pressure Use normal force and the actual contact area.
Journey Tracker
Progress
0/10
1

WONDER — The Mystery

The Same Force, a Different Pressure

A broad support and a narrow support carry the same perpendicular force. Why can they produce different average contact pressures? If the applied force is tilted, which part of it compresses the surface? Pressure connects the normal push to the actual contact area.

Contact modelNormal force measuredContact area measured
Given conditions only; arrows and distances are schematic.

Model: Average compressive contact pressure is the magnitude of normal force divided by contact area. For a uniform pressure, normal force is PA. Pressure is scalar; the associated force on a surface is a vector normal to that surface. The foundation in Stage 3 has its own supplied elastic law; penetration or damage cannot be predicted from pressure alone without material information.

2

PREDICT — Commit to Your Answer

DOK 2 — Predict

A 48 N perpendicular force acts on either a broad pad of area 0.080 m² or a narrow pad of area 0.020 m². Compare the average pressure from the narrow pad with that from the broad pad.

Pad-comparison givensNormal force: 48 NBroad area: 0.080 m²Narrow area: 0.020 m²
Given conditions only; arrows and distances are schematic.

Commit to both a prediction and a reason before revealing the explanation.

Step 1: Pick your answer.

STOP! Before revealing — why did you pick that?

3

▶ PLAY — Live Pressure Ramp on an Elastic Foundation

DOK 2 — Investigate

Predict, measure and compare

Compare two contact areas with the same final applied force and force angle. Then change only final force from one of that pair. Complete three matched runs. Watch the loaded plate move and the foundation compress as normal force and pressure rise. Compare pressure with the model’s deformation, keeping its stiffness fixed.

A massless rigid square plate presses uniformly on an ideal elastic foundation. Its supplied pressure-to-compression stiffness is K = 100000 Pa/m, giving pressure P = Kδ. Applied force rises linearly from zero to the chosen final value over 2 physical seconds, played over 8 real seconds. Angle is measured from the downward surface normal. The guide carries the horizontal force component; normal force is F cos(angle). Quasi-static motion ignores inertia and damping, and plate weight is zero. The plate’s drawn width represents the square root of contact area; vertical compression uses 400 pixels/m. This is a specific elastic model, not a universal relation between pressure and dent depth or a universal cutting threshold.

Use the labelled readouts.

Status: Ready

Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.

Average Pressure vs Physical Time

Use the labelled readouts.

Measurements

Physical elapsed time:
Current applied force magnitude:
Current normal force magnitude:
Horizontal force carried by guide:
Actual contact area:
Average compressive pressure:
Foundation compression:
Stored elastic energy:

Load givens — then predict and run

Loading a setup earns no trial credit.

4

♢ DISCOVER — Normal Force, Area, Units and Model Limits

DOK 1 — Recall

Flip all 4 rule cards. Keep the quantities and model conditions clear.

Rule 1

The perpendicular component

Click to flip

The perpendicular component

Paverage = Fnormal/A. If the applied force makes angle θ with the surface normal, Fnormal = F cos θ. A tangential component does not contribute to this average compressive pressure.

Rule 2

Area and force are independent

Click to flip

Area and force are independent

With normal force fixed, P is inversely proportional to A. With area fixed, P is proportional to normal force. Changing both can leave pressure unchanged.

Rule 3

SI units and squared conversions

Click to flip

SI units and squared conversions

1 Pa = 1 N/m²; 1 kPa = 1000 Pa. 1 cm² = 10⁻⁴ m² and 1 mm² = 10⁻⁶ m². A rectangular contact area is length times width, in consistent units.

∫

Rule 4

Pressure is scalar; response needs a model

Click to flip

Pressure is scalar; response needs a model

Pressure has magnitude and no vector direction. Its surface force has a normal direction. Material deformation, cutting or failure depends on material properties and geometry as well as pressure.

Flip all 4 cards to reveal the rules. 0/4 flipped
5

MISCONCEPTION ATTACK — Destroy the Myths

DOK 2 — Analyze

Choose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.

Myth 1: “Equal applied forces always give equal pressure.”

Myth 2: “A pressure above 10000 Pa must cut or pierce every material.”

6

✦ THE SECOND “AHA!” — Pressure Without the Common Shortcuts

DOK 2 — Apply

Use the normal component, calculate the actual area and convert squared units carefully.

Progress
0/4
Contact modelNormal force measuredContact area measured
Given conditions only; arrows and distances are schematic.

1

Instructor Q1 — The Appropriate Force

Which force belongs in average compressive contact pressure?

2

Instructor Q2 — Doubling Both Quantities

Normal force and contact area both double. What happens to average pressure?

3

Instructor Q3 — A Fresh Pressure

A 72 N normal force acts uniformly over 0.060 m². Find pressure in Pa.

Contact givensNormal force: 72 NArea: 0.060 m²
Given conditions only; arrows and distances are schematic.
Pa
4

Instructor Q4 — Find the Normal Force

Uniform pressure is 6.0 kPa over area 0.015 m². Find the normal force in N.

Force givensUniform pressure: 6.0 kPaArea: 0.015 m²
Given conditions only; arrows and distances are schematic.
N
7

✎ PRACTICE — Independent Surface-Pressure Cases

DOK 1–3 — Practice
DOK 1 — Routine

Challenge 1: A Four-Block Stack

Four identical blocks each have weight 18.0 N. They form one vertical stack at rest. The lowest block contacts a level table over area 0.030 m². Find the stack’s average contact pressure on the table.

Stack givensFour blocks at restWeight of each: 18.0 NBottom contact: 0.030 m²
Given conditions only; arrows and distances are schematic.
Pa
DOK 2 — Application

Challenge 2: Three Possible Faces

A rectangular block has mass 9.0 kg and dimensions 0.10 m × 0.20 m × 0.30 m. It rests on a level table on any one of its three face types. Take g = 10 N/kg. Find the maximum and minimum average contact pressures.

Block givensMass: 9.0 kgSides: 0.10, 0.20, 0.30 mg: 10 N/kgBlock at rest
Given conditions only; arrows and distances are schematic.
Pa
Pa
DOK 3 — Audit & Justify

Challenge 3: Audit a Tilted-Force Report

A 100 N force acts on a horizontal plate at 60° to its downward normal. The rectangular contact face is 2.0 cm by 5.0 cm. Plate weight is negligible and a guide carries the tangential component. A report uses the full applied force for pressure, treats the numerical area in cm² as the same numerical area in m², and describes pressure as a downward vector. Find the contact area in m², normal force in N and average pressure in kPa. Explain all three errors.

Tilted-force givensApplied force: 100 NAngle to normal: 60°Contact: 2.0 cm × 5.0 cmWeight negligibleGuide carries tangentnormal
Given conditions only; arrows and distances are schematic.
m²
N
kPa
8

☷ CHALLENGE — Sort Pressure, Geometry and Response

DOK 2 — Apply

Sort Pressure, Geometry and Response

Classify each statement by the physical idea it describes.

0 / 6 correct

9

TEACH — The Feynman Technique

DOK 3 — Teach

Your Final Mission: Explain why the same perpendicular force produces more average pressure on a smaller contact area. Explain what changes for an angled applied force and why a pressure value alone does not predict how every material will deform.

Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.

Type Your Explanation (≥ 3 sentences)

Final reward below

Hidden exam secrets inside — Crest's private notebook.