WONDER — The Mystery
Why Equal Energy Gives Unequal Temperature Changes
Equal masses of two materials begin at the same temperature and each absorbs the same energy. One warms much more. Specific heat capacity measures the energy per kilogram needed for a one-Kelvin temperature rise under stated conditions. A mixing experiment must also account for the container.
Model: Use constant specific heat capacity and Q = mcΔT for temperature changes without phase change under the stated calorimetric conditions. For an isolated mixing experiment, include every body’s energy change, including the calorimeter. Uniform temperatures, negligible environmental loss and negligible mechanical work are assumed. Use water c = 4200 J/(kg K) as a rounded model value.
PREDICT — Commit to Your Answer
DOK 2 — PredictTwo equal-mass samples begin at the same temperature. A has c = 4200 J/(kg K), B has c = 2000 J/(kg K). Both absorb the same energy, with no phase change. Which has the larger temperature rise?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
B has the larger rise: ΔT = Q/(mc). The B-to-A rise ratio is 4200/2000 = 2.1 under the supplied equal-input assumptions.
▶ PLAY — Live Metal–Water Calorimeter
DOK 2 — InvestigatePredict, measure and compare
Complete two runs changing only metal mass, then a third changing only water mass from one of that pair. Watch the immersed metal and stirred water respond, compare their moving thermometer columns, and check that the water and calorimeter gains equal the metal loss.
The metal is already immersed at t = 0 and remains internally uniform. Take cmetal = 450 J/(kg K), cwater = 4200 J/(kg K), calorimeter capacity Ccal = 100 J/K, and contact conductance G = 10 W/K. The water and calorimeter share one well-mixed temperature and begin at the selected water temperature. Set Cm = mm cm and Cr = mw cw + Ccal. The exact lumped contact response has weighted equilibrium Tf = (Cm Tm0 + Cr Tw0)/(Cm + Cr) and temperature difference (Tm0 − Tw0)e^(−t/τ), with τ = Cm Cr/[G(Cm + Cr)]. The enclosure loses no energy; negligible stirring work and no boiling/phase change are assumed. Stirring markers show prescribed mixing, not computed fluid dynamics. The 180 s physical interval plays over 8 real seconds. The endpoint retains any small remaining temperature difference.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Specific Heat and Full Energy Balances
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Specific heat versus heat capacity
Click to flip
Specific heat versus heat capacity
Specific heat c is energy per unit mass per temperature rise, in J/(kg K). Object heat capacity C = mc is in J/K and depends on mass. They are not interchangeable.
Rule 2
Temperature-change energy
Click to flip
Temperature-change energy
For the stated no-phase-change constant-c process, Q = mc(Tf − Ti). Differences have equal numerical values in K and °C. Do not add 273.15 to a temperature difference.
Rule 3
Include the calorimeter
Click to flip
Include the calorimeter
In isolated mixing, sum all signed energy changes to zero. A cooler calorimeter takes energy too: mmetal cmetal(Tf − Tm0) + mwater cwater(Tf − Tw0) + Ccal(Tf − Tcal0) = 0.
Rule 4
Measurements need controls
Click to flip
Measurements need controls
Measure masses and initial/final temperatures, stir for a uniform reading and reduce environmental loss. Heater experiments must consider energy absorbed by the container and lost to surroundings. A straight electrical-energy calculation alone can overestimate a sample’s heat capacity.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “The final mixing temperature is always the average of the two initial readings.”
Correct — the claim is false.
False. It is weighted by heat capacities under the no-loss, constant-c, no-phase-change assumptions. The calorimeter can provide a third contribution.
Myth 2: “A material with high specific heat always heats more slowly regardless of mass and absorbed power.”
Correct — the claim is false.
False. Temperature rate depends on absorbed power divided by total heat capacity. Mass, container capacity and losses matter as well as material c.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Mass, Specific Heat and the Container
DOK 2 — ApplyUse complete experimental givens rather than ranking materials by c alone.
Instructor Q1 — A Unit Test
Which quantity has units J/K?
Instructor Q2 — Container Correction
A hot metal warms water and a cooler calorimeter inside an insulated enclosure. What must be balanced?
Instructor Q3 — Heating Water
0.200 kg water warms from 18°C to 43°C without phase change. Use c = 4200 J/(kg K). Find energy absorbed by the water.
Instructor Q4 — Find a Material Property
A 0.300 kg sample absorbs 4500 J and rises by 25.0 K, without phase change or loss. Find its specific heat capacity.
4/4 — Instructor Questions Completed
The relevant “thermal size” is heat capacity mc, and the energy balance belongs to the whole chosen system.
✎ PRACTICE — Independent Calorimetry Measurements
DOK 1–3 — PracticeChallenge 1: Warming a Sample
0.350 kg water warms from 22.0°C to 52.0°C. Take c = 4200 J/(kg K), with no phase change. Find the temperature rise in K and energy absorbed by the water.
Step-by-Step Solution
Temperature rise = 52.0 − 22.0 = 30.0 K. Water absorbs Q = 0.350(4200)(30.0) = 44100 J. This is the water’s energy, not automatically the heater’s total output.
Challenge 2: Measure an Unknown Metal
A 0.300 kg metal at 90.0°C is immersed in 0.200 kg water at 20.0°C. The calorimeter has heat capacity 60.0 J/K and also starts at 20.0°C. Final equilibrium is 25.0°C. Use water c = 4200 J/(kg K). Assume no environmental loss, work or phase change. Find the combined water/calorimeter energy gain and the metal’s specific heat capacity.
Step-by-Step Solution
Water gains 0.200(4200)(5.0) = 4200 J; calorimeter gains 60.0(5.0) = 300 J, total 4500 J. Thus 0.300c(90.0 − 25.0) = 4500, giving c = 230.769 J/(kg K). Omitting the calorimeter underestimates this inferred c.
Challenge 3: Audit a Mixing Report
An insulated calorimeter of capacity 140 J/K holds 0.300 kg water with c = 4200 J/(kg K), both initially at 20°C. A 0.500 kg metal with c = 400 J/(kg K) starts at 90°C and is added. No work or phase change occurs. A report uses the arithmetic mean of the initial temperatures, ignores the calorimeter’s energy gain, and adds 273.15 to every temperature change. Find final equilibrium temperature, energy released by the metal and energy gained by the calorimeter. Explain all three errors.
Step-by-Step Solution
Cmetal = 0.500(400) = 200 J/K. Cwater = 0.300(4200) = 1260 J/K; water plus calorimeter has 1400 J/K. Tf = [200(90) + 1400(20)]/1600 = 28.75°C.
Metal releases 200(90 − 28.75) = 12250 J. Calorimeter gains 140(28.75 − 20) = 1225 J. Water gains 1260(8.75) = 11025 J, completing the balance.
The mean must be heat-capacity weighted, not simply arithmetic. The calorimeter is an energy-receiving body and cannot be omitted here. Celsius and Kelvin differences are equal: their offsets cancel, so no 273.15 is added to a temperature change.
☷ CHALLENGE — Sort Properties, Changes and Experimental Balance
DOK 2 — ApplySort Properties, Changes and Experimental Balance
Match each statement to its role.
0 / 6 correct
Physics Insight
A complete experiment requires more than substituting three numbers.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain why high specific heat allows water to absorb substantial energy with a modest temperature rise. Distinguish specific heat from total heat capacity, and explain why a mixing experiment must include the calorimeter and use temperature differences without offsets.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 8.4 — Calorimetry & Specific Heat
Balance every body’s energy. Include the calorimeter.
1. Definitions with units
Specific heat capacity c is energy per unit mass required for a one-Kelvin temperature rise under specified conditions. Its units are J/(kg K). Heat capacity C is the corresponding property of a whole object, in J/K, with C = mc for a uniform material. Water’s rounded c = 4200 J/(kg K) is a supplied model value, not a universal exact constant.
For this constant-c, no-phase-change process: Q = mcΔT
Use mass in kg, and ΔT = Tf − Ti. Celsius and Kelvin differences are numerically equal. Specific heat values in J/(kg °C) and J/(kg K) have equal numerical values. Offset conversion is for temperature readings, not differences.
2. Temperature rise and heating rate
At fixed energy absorbed and mass, ΔT is inversely proportional to c. At fixed absorbed power with negligible losses, dT/dt = P/(mc). Different masses and containers can reverse a comparison based only on c. Water has a high specific heat relative to many common materials, but calling it the highest or ideal coolant in every application is unwarranted; freezing, boiling, corrosion and other properties also matter.
3. Mixing: include every body
Σ Ci(Tf − Ti) = 0 for the stated isolated no-work, no-phase-change model
Use each material’s own mass and specific heat and include calorimeter capacity separately. Tf is a weighted mean of all initial temperatures. A simple two-temperature arithmetic mean requires equal total capacities at those two temperatures. If there are phase changes, external losses or work, add the appropriate energy terms.
A dramatic 1000°C metal example cannot use constant room-temperature properties indiscriminately. Even the simple 1 kg iron/10 kg water calculation with c values 450 and 4186 would give about 20.5°C rather than the original 12°C claim. This audited lesson uses moderate supplied conditions and explicitly avoids boiling or phase changes.
4. Measuring c
For electrical heating, measure mass, initial/final temperatures and input energy using power × time or VIt when appropriate. Include energy absorbed by the heater/container and environmental loss. Ignoring these can make a calculated sample c too large. Insulate, stir and use an appropriate temperature probe; repeated measurements can reveal losses.
In a hot-metal mixing experiment, inferred c follows the metal’s energy release equaling all cold-system gains. Ignoring a cooler calorimeter underestimates the hot metal’s c, while unaccounted environmental loss can also bias the result.
5. Worked independent cases
The 0.350 kg water sample rises 30.0 K and absorbs 44100 J. In the unknown-metal case, water gains 4200 J and the calorimeter 300 J; total 4500 J gives cmetal = 230.769 J/(kg K).
The report audit has Cmetal = 200 J/K, Cwater = 1260 J/K and Ccal = 140 J/K. Tf = 28.75°C. Metal releases 12250 J, shared as 11025 J to water and 1225 J to the calorimeter. Offsets cancel in temperature changes.
6. Live immersed-metal model
At t = 0 the metal is immersed. The water is stirred and shares one temperature with the calorimeter. Treat Cm = mm(450), Cr = mw(4200) + 100, and G = 10 W/K. No energy leaves the whole enclosure and stirring work is neglected.
Tf = (Cm Tm0 + Cr Tw0)/(Cm + Cr); τ = Cm Cr/[G(Cm + Cr)]
D(t) = (Tm0 − Tw0)e^(−t/τ). Tmetal = Tf + Cr D/(Cm + Cr); Twater = Tf − Cm D/(Cm + Cr). Metal release equals water gain plus calorimeter gain at every instant, not only at equilibrium. The displayed energy residual checks this identity.
The metal is shown submerged; column heights follow actual temperatures on a 0–100°C scale. Fluid markers circulate schematically to represent prescribed stirring. The model does not calculate fluid dynamics. One hundred eighty physical seconds play over eight real seconds; remaining temperature differences at the endpoint are retained.
Compare metal masses, then water masses with other controls fixed. Three matched completed runs unlock the next stage. Run, Pause, Step, Reset, paused reload and reduced-motion behavior use the same clock.
7. Course scope
Cambridge A Level 9702 topic 14.3 covers specific heat capacity. AP Physics 2 topic 9.5 covers constant-c temperature-change energy; 9.3 supports equilibrium. The lumped exponential contact dynamics are a clearly stated extension for the live display.
✓ Crest’s Checklist
- I distinguish c in J/(kg K) from C in J/K.
- I use temperature changes with no offset.
- I compare masses and absorbed energy or power fairly.
- I include calorimeter and other receiver capacities.
- I state constant-property, loss and phase assumptions.
- I check the complete signed energy balance.
— Crest ☆ “Balance every body’s energy. Include the calorimeter.”
Mission 8.4 Complete! · All 10 levels cleared · PHYSICS CREST
★ Calorimetry & Specific Heat Master
The relevant “thermal size” is heat capacity mc, and the energy balance belongs to the whole chosen system.