WONDER — The Mystery
Which Connections Actually Light a Lamp?
A lamp has two electrically distinct contacts joined by its filament. It lights when a potential difference drives current through that filament along a complete conducting path. A lead to just one isolated contact leaves the path open. One wire plus a direct conducting contact can complete the path: the number of loose wires is not the deciding rule.
Model: Treat connecting wires and closed switches as ideal conductors. The model source has a finite internal resistance of 1 Ω. The lamp is represented by a fixed resistor, so brightness is only a qualitative power indicator. Ignore switching transients and analyze steady state.
PREDICT — Commit to Your Answer
DOK 2 — PredictA lamp has one terminal connected to a source. Its other terminal is isolated. What happens after switching transients have settled?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
An isolated second contact leaves an open path. There is no steady filament current; wire count alone does not determine whether a loop exists.
▶ PLAY — Live Open, Closed & Bypass Lab
DOK 2 — InvestigatePredict, measure and compare
Run two source e.m.f.s with the same closed path, then change only the path mode. Complete three runs. Closed paths show moving markers; the open path stops steady flow; the bypass moves charge around the load.
Path modes: 0 = open series switch, 1 = closed switch, 2 = closed switch with an ideal wire bypass across the load. The source has fixed internal r = 1 Ω, making bypass current finite. The load has resistance R. A run lasts 8 model seconds over 8 real seconds. With an open switch, I = 0 and all terminal p.d. is across the gap. With a closed loop, I = ε/(R + 1). In bypass mode, external p.d. and load current are zero while source current is ε/1. Marker speed is schematic conventional current.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Connections Determine the Path
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
A loop and driving p.d.
Click to flip
A loop and driving p.d.
Steady current in a resistive DC path requires a complete conducting loop and a source that maintains a p.d. A closed circuit with zero driving p.d. has no steady current.
Rule 2
An open series path
Click to flip
An open series path
A gap in the only path gives zero steady current. It can still have nonzero p.d. across the gap. The statement applies after transients have settled.
Rule 3
A bypass is a different path
Click to flip
A bypass is a different path
A very low-resistance parallel path can bypass a load. An ideal wire across it gives zero load p.d.; finite source or wire resistance is needed to calculate a finite short current.
Rule 4
Contacts, not loose-wire count
Click to flip
Contacts, not loose-wire count
Both lamp contacts must connect into the complete loop. One wire and one direct conducting contact can suffice. Connecting both source leads to the same lamp contact bypasses the filament.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “An open switch has zero voltage because its current is zero.”
Correct — the claim is false.
False. A gap can have the full source terminal p.d. while carrying no steady current.
Myth 2: “A bypass always makes the bypassed lamp brighter.”
Correct — the claim is false.
False. An ideal wire bypass gives zero lamp p.d. and therefore zero lamp power.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Path Tests and Steady Measurements
DOK 2 — ApplyAssume ideal wires and settled DC conditions; distinguish load current from source current.
Instructor Q1 — One Contact
Only one isolated lamp contact is connected to a source. What is missing?
Instructor Q2 — A Closed Unpowered Loop
A resistor and wires form a closed loop without a source or other driving p.d. What is its settled current?
Instructor Q3 — Closed Path
A 12 V source with internal r = 2 Ω is connected to an 8 Ω load. Find the steady current.
Instructor Q4 — Open Gap
A 7 V source is connected to a resistor and open series switch. Find the steady current.
4/4 — Instructor Questions Completed
Trace nodes and paths before predicting which components carry current.
✎ PRACTICE — Independent Connection Audits
DOK 1–3 — PracticeChallenge 1: Open Series Switch
An ideal 8 V source, a 4 Ω load and one series switch form a loop. The switch is open. Find the settled current and p.d. across the open switch.
Step-by-Step Solution
I = 0. The load has no resistive drop; the switch gap has 8 V across it.
Challenge 2: Complete Path
A source of e.m.f. 9 V and internal resistance 0.5 Ω drives a 4 Ω load through a closed switch and ideal wires. Find source current, terminal p.d. and load power.
Step-by-Step Solution
I = 9/(4 + 0.5) = 2 A. Vterminal = 2 × 4 = 8 V. Pload = 2² × 4 = 16 W.
Challenge 3: Audit the Bypass Report
A source has e.m.f. 6 V and internal resistance 1.5 Ω. A 4.5 Ω lamp is connected across its terminals, and an ideal wire is also connected directly across the lamp. The report says the wire opens the loop, source current becomes zero, and the lamp becomes brighter. Find source current and lamp power. Explain all three errors.
Step-by-Step Solution
The bypass completes a low-resistance path; it is not an open circuit. I = 6/1.5 = 4 A, limited by internal resistance. The ideal bypass gives zero terminal and lamp p.d., so lamp power is zero rather than greater.
☷ CHALLENGE — Closed, Open or Bypassed?
DOK 2 — ApplyClosed, Open or Bypassed?
Classify each stated topology; a bypassed load may be inside a circuit with substantial source current.
0 / 6 correct
Physics Insight
A circuit can carry source current while a bypassed load carries none.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain the need for a complete path and driving p.d., why a gap can have voltage without current, and how a bypass differs from an open circuit.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 10.2 — Circuit Requirements & Switches
Trace complete paths and distinguish open circuits from bypasses.
1. The complete-path test
A source plus load must have a conducting return path. Existing carriers throughout the circuit respond to the electric field. They do not wait for a newly created electron to arrive from the battery.
2. Open and closed switches
A closed ideal switch has negligible p.d. across it. An open switch in the only branch has zero steady current. It can support the source p.d. across the gap; zero current does not imply zero voltage.
3. Short and bypass paths
A short is a very low-resistance connection, often across a component or source terminals. An ideal bypass across a lamp fixes its p.d. to zero. A real source or wire has resistance that limits short current; shorting an ideal voltage source with an ideal zero-resistance wire has no finite steady solution.
4. Lamp anatomy
The side and bottom contacts are electrically distinct, with the filament between them. What matters is the connections. A single wire plus direct conducting contact can complete a loop; simply counting loose wires is unreliable.
5. Branches and transients
Opening one parallel branch stops current in that branch without necessarily breaking another complete branch. A switch change can have brief transient effects; this mission analyzes the settled DC limit.
Worked practice
C1: 0 A and 8 V across the gap. C2: 2 A, 8 V and 16 W. C3: a complete bypass path gives source current 4 A, limited by internal resistance; the lamp has 0 V and 0 W.
Experiment and access
Path modes: 0 = open series switch, 1 = closed switch, 2 = closed switch with an ideal wire bypass across the load. The source has fixed internal r = 1 Ω, making bypass current finite. The load has resistance R. A run lasts 8 model seconds over 8 real seconds. With an open switch, I = 0 and all terminal p.d. is across the gap. With a closed loop, I = ε/(R + 1). In bypass mode, external p.d. and load current are zero while source current is ε/1. Marker speed is schematic conventional current.
Predict before Run. Complete three matched measurements; loading a preset does not complete a trial. Pause, Step and Reset work offline. Saved progress resumes paused. Reduced-motion preference uses a completed snapshot on Run. Hints and solutions become available only after a genuine numerical attempt and do not complete a challenge. Teaching checks effort; compare your explanation with these notes or a teacher.
Course scope
Cambridge AS 9702 topic 10.1 covers practical circuits and component symbols. AP Physics 2 topic 11.2 distinguishes closed, open and short circuits; topic 11.5 supplies the nonideal-source model used here.
✓ Crest’s Checklist
- I trace both load contacts.
- I state settled DC assumptions.
- I distinguish open from bypass paths.
- I allow voltage across an open gap.
- I include finite resistance when calculating a short current.
— Crest ☆ “Trace complete paths and distinguish open circuits from bypasses.”
Mission 10.2 Complete! · All 10 levels cleared · PHYSICS CREST
★ Circuit Requirements & Switches Master
Trace nodes and paths before predicting which components carry current.