WONDER — The Mystery
A Material Name Is Not Enough
Two wires made of the same material can have different resistances because their lengths and cross-sectional areas differ. Conversely, a sufficiently thick wire of a higher-resistivity material can have lower resistance than a thin wire of another material. Compare geometry and material under the same temperature conditions.
Model: Use a uniform ohmic wire with constant cross-sectional area, uniform temperature and resistivity. R = ρL/A applies along its length. Ignore contact resistance and self-heating changes in the simulation by holding temperature constant. Resistivity is a material property under specified conditions, not a universal temperature-independent constant.
PREDICT — Commit to Your Answer
DOK 2 — PredictTwo uniform wires have the same material and temperature. Wire B is twice as long as A and has the same cross-sectional area. How do their resistances compare?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
R = ρL/A, so doubling L at fixed ρ and A doubles resistance. The material resistivity does not change merely because geometry changes.
▶ PLAY — Live Uniform-Wire Resistance Lab
DOK 2 — InvestigatePredict, measure and compare
Measure two wire lengths with area and resistivity fixed, then change only cross-sectional area. Complete three runs. Watch conventional-current markers circulate and thermal energy accumulate under the fixed 3 V supply.
An ideal 3 V source drives one uniform ohmic wire at constant temperature. ρ is entered in units of 10⁻⁶ Ω m, length in m and cross-sectional area in mm². R = ρL/A and I = 3/R. Thermal energy transferred is I²Rt. A run lasts 8 model seconds over 8 real seconds. The drawn resistive section has a fixed length scale of 40 pixels per metre; its transverse thickness indicates relative area schematically. Moving dots show conventional current with schematic speed. Temperature is held constant by an ideal thermal reservoir, so accumulated transferred energy does not change ρ during a run.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Geometry and Material Are Different
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Define resistance
Click to flip
Define resistance
R = V/I at a specified operating point. For an ohmic conductor at constant physical conditions, R is independent of applied V within its ohmic range.
Rule 2
Uniform-wire geometry
Click to flip
Uniform-wire geometry
R = ρL/A. At fixed ρ, R is proportional to L and inversely proportional to cross-sectional A. For a circular wire A = πd²/4; doubling diameter quadruples area.
Rule 3
Material and conditions
Click to flip
Material and conditions
Resistivity has units Ω m and depends on material and conditions such as temperature. It does not depend on wire length or area in this uniform-material model.
Rule 4
Temperature is conditional
Click to flip
Temperature is conditional
Most metals have higher resistance as temperature increases. NTC thermistors decrease resistance with increasing temperature; LDR resistance decreases with increasing illumination. Avoid an all-material temperature rule.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Doubling a circular wire’s diameter doubles its cross-sectional area.”
Correct — the claim is false.
False. Area is proportional to diameter squared, so it quadruples.
Myth 2: “Every material’s resistance rises when it gets hotter.”
Correct — the claim is false.
False. This is typical of metals over ordinary ranges, while an NTC thermistor decreases resistance.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Geometry, Scaling and SI Units
DOK 2 — ApplyAssume uniform wires and unchanged temperature unless stated otherwise.
Instructor Q1 — Area Change
A wire’s area doubles while length and resistivity stay fixed. What happens to R?
Instructor Q2 — Material Property
Which quantity describes the material under specified conditions, rather than the entire component geometry?
Instructor Q3 — Uniform Wire
A uniform wire has ρ = 4.0 × 10⁻⁷ Ω m, L = 3 m and A = 2 mm². Find resistance.
Instructor Q4 — Material Resistivity
A uniform wire of length 2 m and area 0.5 mm² has resistance 1.2 Ω. Find resistivity.
4/4 — Instructor Questions Completed
Hold conditions fixed and compare ρL/A, not just material names or diameters.
✎ PRACTICE — Independent Wire Audits
DOK 1–3 — PracticeChallenge 1: Calculate Resistance
At a stated fixed temperature, a uniform wire has resistivity 2.4 × 10⁻⁷ Ω m, length 3 m and cross-sectional area 0.8 mm². Find its resistance.
Step-by-Step Solution
A = 0.8 × 10⁻⁶ m²; R = 2.4 × 10⁻⁷ × 3/(0.8 × 10⁻⁶) = 0.9 Ω.
Challenge 2: Stretch at Constant Volume
A uniform wire initially has resistance 1.2 Ω and area 1.0 mm². It is stretched uniformly to 2.5 times its original length with its volume and resistivity unchanged. Find its new area and resistance.
Step-by-Step Solution
LA is constant, so Anew = 1/2.5 = 0.4 mm². Rnew/Rold = 2.5/(1/2.5) = 6.25; Rnew = 7.5 Ω.
Challenge 3: Audit a Wire Report
A circular uniform wire has ρ = 3.0 × 10⁻⁷ Ω m, L = 4 m and A = 0.6 mm². A second wire of the same material and length has twice its diameter at the same temperature. A report says resistivity includes the wire’s length, twice the diameter means twice the area, and warming any material must increase resistance. Find both wire resistances and explain all three errors.
Step-by-Step Solution
First R = 3 × 10⁻⁷ × 4/(0.6 × 10⁻⁶) = 2 Ω. Twice the diameter gives four times the area, 2.4 mm², and Rsecond = 0.5 Ω. Resistivity is a material property at given conditions, not length-dependent. Warming usually increases a metal’s R, but an NTC thermistor decreases R, so the universal claim fails.
☷ CHALLENGE — Increase, Decrease or Unchanged?
DOK 2 — ApplyIncrease, Decrease or Unchanged?
Compare resistance with all unmentioned variables fixed and with unchanged resistivity except where explicitly stated.
0 / 6 correct
Physics Insight
A diameter change affects area quadratically.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain resistance versus resistivity, the effects of length and area, how diameter affects area, and why temperature claims require a named material.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 10.4 — Resistance & Resistivity
Compare material, length and cross-sectional area under stated conditions.
1. Resistance and resistivity
Resistance R = V/I has units Ω. Resistivity ρ has units Ω m. R belongs to the component and depends on geometry, material and physical conditions. ρ belongs to the material under specified conditions. Ohmic behavior means constant R as V changes while relevant physical conditions, especially temperature, are fixed.
2. Uniform-wire equation
R = ρL/A for a uniform wire with constant cross-sectional area and uniform resistivity. Use length in m and area in m². 1 mm² = 10⁻⁶ m²; 1 cm² = 10⁻⁴ m². The relevant area is across the wire, not its lateral surface area.
3. Diameter and stretching
For a circular wire A = πr² = πd²/4. Doubling diameter gives four times area and a quarter of the resistance if L and ρ stay fixed. When a wire stretches with constant volume LA and unchanged ρ, an s-fold increase in length gives an s²-fold resistance increase.
4. Material comparisons
Compare ρL/A for each specimen. Lower resistivity alone does not prove a particular wire has lower resistance unless geometry and conditions are controlled. A thick higher-resistivity wire can have lower R than a thin lower-resistivity wire.
5. Temperature and illumination
In ordinary metals, increased lattice vibration usually increases electron scattering and resistivity. An NTC thermistor’s R decreases as temperature rises; an LDR’s R decreases with increasing illumination. These are qualitative device trends and are not a universal linear formula.
6. Thermal energy and current
For a fixed voltage, increasing R reduces I and P = V²/R. For a fixed current, increasing R increases I²R heating. Always state what is held constant before linking resistance to heating. Current is charge flow rate, not the speed of individual carriers.
Worked practice
C1: 0.9 Ω. C2: 0.4 mm² and 7.5 Ω. C3: 2 Ω and 0.5 Ω; material resistivity is separate from length, area changes by four, and NTC behavior disproves the universal heating claim.
Experiment and access
An ideal 3 V source drives one uniform ohmic wire at constant temperature. ρ is entered in units of 10⁻⁶ Ω m, length in m and cross-sectional area in mm². R = ρL/A and I = 3/R. Thermal energy transferred is I²Rt. A run lasts 8 model seconds over 8 real seconds. The drawn resistive section has a fixed length scale of 40 pixels per metre; its transverse thickness indicates relative area schematically. Moving dots show conventional current with schematic speed. Temperature is held constant by an ideal thermal reservoir, so accumulated transferred energy does not change ρ during a run.
Predict before Run. Complete three matched measurements; loading a preset does not complete a trial. Pause, Step and Reset work offline. Saved progress resumes paused. Reduced-motion preference uses a completed snapshot on Run. Hints and solutions become available only after a genuine numerical attempt and do not complete a challenge. Teaching checks effort; compare your explanation with these notes or a teacher.
Course scope
Cambridge AS 9702 topic 9.3 and AP Physics 2 topic 11.3 cover resistance, resistivity and geometry. Cambridge also names NTC thermistors and LDRs; their qualitative trends prevent an incorrect universal temperature rule.
✓ Crest’s Checklist
- I distinguish resistance from resistivity.
- I convert area units before substitution.
- I use diameter squared for circular area.
- I track both length and area when stretching.
- I qualify temperature trends by material.
— Crest ☆ “Compare material, length and cross-sectional area under stated conditions.”
Mission 10.4 Complete! · All 10 levels cleared · PHYSICS CREST
★ Resistance & Resistivity Master
Hold conditions fixed and compare ρL/A, not just material names or diameters.