WONDER — The Mystery
Does Doubling Voltage Always Double Current?
A resistor at fixed physical conditions can have current proportional to its p.d. A filament heats as current increases and its resistance changes. A diode behaves differently in forward and reverse bias. Calculating R = V/I at one operating point does not prove that the component obeys Ohm’s law over a range.
Model: Distinguish the definition R = V/I, where I is nonzero, from Ohm’s law: V is proportional to I with constant resistance under unchanged physical conditions. I–V graphs here place current vertically and p.d. horizontally. The filament and diode equations in the lab are qualitative teaching models, not universal component specifications.
PREDICT — Commit to Your Answer
DOK 2 — PredictAn ohmic resistor at constant temperature carries 0.5 A at 3 V. What current does it carry at 9 V in the same ohmic range?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Tripling p.d. triples current when R stays constant: I = 1.5 A. This comparison requires unchanged physical conditions.
▶ PLAY — Live Voltage Sweep & Circuit
DOK 2 — InvestigatePredict, measure and compare
Measure two target voltages for the same ohmic resistor, then change only the component model to the filament. Complete three sweeps. Watch current markers move while the I–V trace grows; test negative bias for the diode model.
The ideal source p.d. ramps linearly from 0 to the selected target over 8 model seconds, played over 8 real seconds. Mode 0: an ohmic resistor I = V/R0. Mode 1: a qualitative filament characteristic I = V/[R0(1 + |V|/6 V)], representing a higher resistance at larger bias as a filament heats. Mode 2: a simplified diode with zero current at V ≤ 0.6 V and I = (V − 0.6 V)/R0 above threshold; reverse leakage and breakdown are omitted. These are prescribed quasistatic characteristics, not a transient thermal or diode simulation. Markers follow integrated conventional charge with schematic spacing and speed. The graph uses I on the vertical axis and V horizontally.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Live I–V Trace
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — A Definition Is Not a Proportionality Test
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Ohm’s law has conditions
Click to flip
Ohm’s law has conditions
V ∝ I for an ohmic conductor when relevant physical conditions, especially temperature, stay constant. Then its graph passes through the origin with constant slope.
Rule 2
Read the axes
Click to flip
Read the axes
For I vertical and V horizontal, slope = ΔI/ΔV = 1/R for an ohmic line. For V vertical and I horizontal, slope = R. A curved graph’s local gradient is not generally equal to I/V.
Rule 3
A filament heats
Click to flip
A filament heats
A filament’s resistance rises as temperature rises. Its I–V curve becomes shallower on positive bias as V increases. R = V/I can still be found at each nonzero operating point.
Rule 4
A diode is directional
Click to flip
A diode is directional
A diode carries significant forward current above its forward-bias region and very little reverse current before breakdown. The exact curve and turn-on scale depend on the device and temperature.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “V = IR at one point proves a component is ohmic.”
Correct — the claim is false.
False. R = V/I defines an operating-point resistance; constant R across a controlled range is the Ohm’s-law test.
Myth 2: “The slope of any I–V graph is the resistance.”
Correct — the claim is false.
False. With I vertical, an ohmic slope is 1/R; a nonlinear tangent describes differential conductance.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Controlled Comparisons and Axis Reading
DOK 2 — ApplyState what stays fixed and distinguish a point resistance from an ohmic line slope.
Instructor Q1 — Fixed Source
V stays fixed and an ohmic resistance doubles. What happens to current?
Instructor Q2 — Filament Test
A filament has different values of V/I at two operating points as it warms. What follows?
Instructor Q3 — Ohmic Current
An ohmic 5.5 Ω resistor is held at constant temperature under 11 V. Find current.
Instructor Q4 — Graph Slope
An ohmic graph has I vertically and V horizontally. Its slope is 0.25 A/V. Find resistance.
4/4 — Instructor Questions Completed
Check proportionality across a range and state the graph axes and physical conditions.
✎ PRACTICE — Independent Ohm’s-Law Audits
DOK 1–3 — PracticeChallenge 1: Operating Point
A component has p.d. 9 V and current 0.30 A at one operating point. Find its resistance at this point.
Step-by-Step Solution
R = V/I = 9/0.30 = 30 Ω. This point alone does not prove Ohm’s law.
Challenge 2: Controlled Ohmic Data
An ohmic resistor at constant temperature carries 0.40 A at 2 V and 1.20 A at 6 V. Find its resistance and current at 10 V, within the same ohmic range.
Step-by-Step Solution
R = 2/0.40 = 6/1.20 = 5 Ω. I = 10/5 = 2 A.
Challenge 3: Audit the Filament Report
A filament carries 0.40 A at 2 V and 0.80 A at 6 V after settling at each setting. A report calls it a device with one unchanging resistance, states that the slope of an I-vertical/V-horizontal graph equals resistance, and says temperature never matters for Ohm’s law. Find the point resistance at each setting and explain all three errors.
Step-by-Step Solution
R1 = 2/0.40 = 5 Ω and R2 = 6/0.80 = 7.5 Ω, so resistance is not constant. A filament heats and changes resistance. For an ohmic I-vertical/V-horizontal line, slope is 1/R, not R; a nonlinear local slope is differential conductance. Ohm’s law requires unchanged physical conditions, especially temperature.
☷ CHALLENGE — Current Up, Down or Unchanged?
DOK 2 — ApplyCurrent Up, Down or Unchanged?
Use an ohmic resistor under the stated fixed physical conditions and compare positive current magnitudes.
0 / 6 correct
Physics Insight
A proportional comparison is meaningful only after identifying what stays fixed.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain R = V/I versus Ohm’s law, how temperature changes a filament’s curve, and how the two possible graph axis choices change the meaning of slope.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 10.5 — Ohm’s Law & I–V Characteristics
Test proportionality under controlled conditions and read the graph axes.
1. Definition and law
At a nonzero current, R = V/I defines resistance at an operating point. Ohm’s law is the special relationship V ∝ I, with constant R under unchanged physical conditions. A single point or the identity V = IR alone does not prove proportionality.
2. Graph axes and slopes
For an ohmic graph with I vertically and V horizontally, slope ΔI/ΔV = 1/R, in A/V. For V vertically and I horizontally, slope ΔV/ΔI = R, in Ω. A nonlinear tangent gives differential conductance or resistance; it is generally different from the point quotient.
3. Filament behavior
A filament heats as its current increases. For a metallic filament, this usually increases resistivity and resistance. Its I–V graph becomes shallower on positive bias. At constant temperature a metallic conductor can be ohmic within its operating range; heating is a change in conditions.
4. Diode behavior
A diode favors forward current and has very small reverse current before breakdown. Its characteristic is nonlinear and depends on device and temperature. The piecewise lab model illustrates direction and a forward threshold, not a universal 0.6 V specification.
5. Zero-current cases
At V = I = 0, the quotient V/I is undefined. For a known ohmic line, resistance can still be inferred from its slope. A blocked diode with nonzero reverse V and zero modeled I has no finite point resistance. Do not divide by zero or assign a finite resistor model without justification.
6. Fixed-variable comparisons
At fixed R, current is proportional to V. At fixed V, current is inversely proportional to R. An ideal source fixes its terminal p.d.; a nonideal source can change terminal p.d. when current changes. State the source model and temperature conditions.
Worked practice
C1: 30 Ω at the given point. C2: 5 Ω and 2 A. C3: 5 Ω and 7.5 Ω; correct the constant-resistance claim, inverse-slope relation and missing temperature condition.
Experiment and access
The ideal source p.d. ramps linearly from 0 to the selected target over 8 model seconds, played over 8 real seconds. Mode 0: an ohmic resistor I = V/R0. Mode 1: a qualitative filament characteristic I = V/[R0(1 + |V|/6 V)], representing a higher resistance at larger bias as a filament heats. Mode 2: a simplified diode with zero current at V ≤ 0.6 V and I = (V − 0.6 V)/R0 above threshold; reverse leakage and breakdown are omitted. These are prescribed quasistatic characteristics, not a transient thermal or diode simulation. Markers follow integrated conventional charge with schematic spacing and speed. The graph uses I on the vertical axis and V horizontally.
Predict before Run. Complete three matched measurements; loading a preset does not complete a trial. Pause, Step and Reset work offline. Saved progress resumes paused. Reduced-motion preference uses a completed snapshot on Run. Hints and solutions become available only after a genuine numerical attempt and do not complete a challenge. Teaching checks effort; compare your explanation with these notes or a teacher.
Course scope
Cambridge AS 9702 topic 9.3 explicitly names metal at constant temperature, filament and diode I–V characteristics. AP Physics 2 topic 11.3 covers Ohm’s law, point resistance and nonconstant resistance. The lab’s specific nonlinear equations are declared qualitative models.
✓ Crest’s Checklist
- I state Ohm’s-law conditions.
- I distinguish point resistance from proportionality.
- I read graph axes before using a slope.
- I describe filament and diode curves.
- I keep amperes, volts and ohms distinct.
— Crest ☆ “Test proportionality under controlled conditions and read the graph axes.”
Mission 10.5 Complete! · All 10 levels cleared · PHYSICS CREST
★ Ohm’s Law & I–V Characteristics Master
Check proportionality across a range and state the graph axes and physical conditions.