WONDER — The Mystery
A Series Element Before a Split
A resistor before a junction carries the source current. Two resistors beyond that junction can share the same pair of nodes and divide the current. Replacing that parallel pair by an equivalent resistance helps find source current, but the internal branch currents must then be recovered from the pair’s p.d.
Model: Use positive finite fixed resistances, ideal wires and a constant-p.d. ideal source. Valid series/parallel reduction preserves behavior at a group’s external terminals. It does not make all original element currents equal. The method applies to reducible networks; other networks require Kirchhoff’s rules directly.
PREDICT — Commit to Your Answer
DOK 2 — PredictR1 lies in series with a true parallel pair R2 and R3. Which is a valid first reduction for a simplify–analyze–expand solution?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Reduce the parallel pair, add its equivalent to R1, find source current, then expand back to the branch p.d. and currents. Kirchhoff’s rules can also analyze the original network directly.
▶ PLAY — Live Mixed Circuit & Equivalent Views
DOK 2 — InvestigatePredict, measure and compare
Measure two source p.d.s with resistors fixed, then change only R1. Complete three runs. Watch current move through R1 and divide into unequal branches. Change view to the reduced pair or total equivalent and confirm that source current stays the same.
R1 is in series with R2 ∥ R3. Rp = R2R3/(R2 + R3), Req = R1 + Rp, I = V/Req, V1 = IR1 and Vp = IRp. Branch currents are I2 = Vp/R2 and I3 = Vp/R3. A run lasts 8 model seconds over 8 real seconds. View 0 shows the original network, view 1 replaces the parallel pair by Rp, and view 2 replaces the complete network by Req. These are analytical equivalents, not physical rewiring. Moving markers show conventional-current routes with schematic speeds and counts; numerical readouts give exact junction and energy balances. Resistor power totals equal ideal source output.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Simplify, Analyze, Expand and Check
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Trace actual nodes
Click to flip
Trace actual nodes
Two elements are parallel only when connected between the same two nodes. Two elements are series only when they carry the same unbranched current. Visual proximity is not enough.
Rule 2
Simplify valid groups
Click to flip
Simplify valid groups
For this topology, reduce R2 ∥ R3 to Rp, then add R1. Other reducible networks may require series groups first or a different reduction order.
Rule 3
Expand back correctly
Click to flip
Expand back correctly
After finding source current, recover the p.d. of each equivalent group. Parallel branch currents use that group p.d., not automatically the full source p.d.
Rule 4
Use conservation and limits
Click to flip
Use conservation and limits
Check I = I2 + I3, V = V1 + Vp and total resistor power = source output. An open branch is not a zero-resistance shortcut. Nonreducible networks may require direct loop and junction equations.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Every resistor in a mixed circuit carries the source current.”
Correct — the claim is false.
False. R1 carries the source current, which divides into the parallel branch currents.
Myth 2: “The parallel pair always has the full source p.d. even with a series resistor.”
Correct — the claim is false.
False. R1 has its own voltage drop; the pair has the remaining p.d.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Reduce, Recover and Verify
DOK 2 — ApplyIdentify the exact group and use its own p.d. when expanding.
Instructor Q1 — Branch Expansion
Which p.d. is used to calculate I2 after reducing R2 ∥ R3 behind R1?
Instructor Q2 — A Different Reducible Pattern
Two parallel branches each contain two series resistors. Which reduction is valid?
Instructor Q3 — Parallel Pair
R2 = 4 Ω and R3 = 12 Ω form a true parallel pair. Find Rp.
Instructor Q4 — Group P.d.
A source of 16 V drives R1 = 2 Ω in series with a group of equivalent resistance 6 Ω. Find the p.d. across the group.
4/4 — Instructor Questions Completed
An equivalent resistor preserves terminal behavior, while expansion recovers the original internal quantities.
✎ PRACTICE — Independent Mixed-Network Audits
DOK 1–3 — PracticeChallenge 1: One Valid Reduction
An ideal source drives R1 = 4 Ω in series with a parallel pair R2 = 6 Ω and R3 = 9 Ω. Find total equivalent resistance.
Step-by-Step Solution
Rp = 6 × 9/(6 + 9) = 3.6 Ω; Req = 4 + 3.6 = 7.6 Ω.
Challenge 2: Recover Branch Current
An ideal 20 V source drives R1 = 2 Ω in series with R2 = 8 Ω and R3 = 8 Ω in parallel. Find source current, the pair p.d. and current in R2.
Step-by-Step Solution
Rp = 4 Ω and Req = 6 Ω. I = 20/6 = 10/3 A; Vp = (10/3) × 4 = 40/3 V. I2 = (40/3)/8 = 5/3 A; I3 is the same, and their sum is 10/3 A.
Challenge 3: Audit Two Series Branches
An ideal 18 V source drives two parallel branches. The upper branch contains A = 2 Ω in series with B = 4 Ω; the lower contains C = 3 Ω in series with D = 9 Ω. A report adds all four resistances directly, assigns one equal current to all four, and treats removing D with a gap as a shorted lower branch. Find initial equivalent resistance, both initial branch currents and source current after D is removed leaving a gap. Explain all three errors.
Step-by-Step Solution
Upper resistance is 2 + 4 = 6 Ω; lower is 3 + 9 = 12 Ω. Req = 6 × 12/(6 + 12) = 4 Ω. Iupper = 18/6 = 3 A and Ilower = 18/12 = 1.5 A. Removing D with a gap opens the lower path, so its current is zero, not a short-circuit current. The upper retains 18 V and 3 A; source current becomes 3 A.
☷ CHALLENGE — Valid Group or Invalid Shortcut?
DOK 2 — ApplyValid Group or Invalid Shortcut?
Classify each proposed group using paths and nodes rather than position.
0 / 6 correct
Physics Insight
The group’s terminal equivalent does not erase its original internal topology.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain simplify–analyze–expand using real path and node definitions, recovery of group p.d. and branch current, conservation checks and the difference between an open and a short.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 10.9 — Combination Circuits
Simplify valid groups, analyze the whole and expand back to branch quantities.
1. Identify topology
Series elements carry a common unbranched current; parallel elements share the same two nodes. A junction between two visually adjacent resistors can prevent a series reduction. A crossing without a connection is not a junction.
2. Simplify this pattern
For R1 in series with R2 ∥ R3: Rp = R2R3/(R2 + R3); Req = R1 + Rp. The equivalent preserves the relationship between total current and terminal p.d., not every internal current.
3. Analyze and expand
Find I = V/Req. Recover V1 = IR1 and Vp = IRp = V − V1. Then I2 = Vp/R2 and I3 = Vp/R3. Using the full source p.d. for each inner branch ignores the R1 drop.
4. Check conservation
Junction: I = I2 + I3. Loop: V = V1 + Vp. Power: VI = I²R1 + I2²R2 + I3²R3. Their energy versions follow by multiplying by a common interval for constant conditions.
5. Another reducible pattern
Two series branches in parallel are reduced by adding within each branch, then combining the branch equivalents reciprocally. Work back into each branch using its full branch p.d. and common branch current. Different branch resistances generally give different currents.
6. Open and short changes
Removing an element and leaving a gap makes its branch open: zero settled current. Replacing it by an ideal wire is a shorted element and a different network. An ideal voltage source directly across an ideal wire has no finite steady-current solution.
7. Limits of the method
Some bridge or multi-loop networks cannot be reduced by direct series/parallel grouping. Use independent Kirchhoff junction and loop equations instead of forcing an invalid combination. The quickest valid reduction order depends on the topology.
Worked practice
C1: Rp = 3.6 Ω and Req = 7.6 Ω. C2: 10/3 A source, 40/3 V across the pair and 5/3 A in each branch. C3: 6 Ω and 12 Ω branches give Req = 4 Ω, currents 3 A and 1.5 A; after the lower gap opens, source current is 3 A.
Experiment and access
R1 is in series with R2 ∥ R3. Rp = R2R3/(R2 + R3), Req = R1 + Rp, I = V/Req, V1 = IR1 and Vp = IRp. Branch currents are I2 = Vp/R2 and I3 = Vp/R3. A run lasts 8 model seconds over 8 real seconds. View 0 shows the original network, view 1 replaces the parallel pair by Rp, and view 2 replaces the complete network by Req. These are analytical equivalents, not physical rewiring. Moving markers show conventional-current routes with schematic speeds and counts; numerical readouts give exact junction and energy balances. Resistor power totals equal ideal source output.
Predict before Run. Complete three matched measurements; loading a preset does not complete a trial. Pause, Step and Reset work offline. Saved progress resumes paused. Reduced-motion preference uses a completed snapshot on Run. Hints and solutions become available only after a genuine numerical attempt and do not complete a challenge. Teaching checks effort; compare your explanation with these notes or a teacher.
Course scope
Cambridge AS 9702 topic 10.2 and AP Physics 2 topics 11.5–11.7 cover resistor combinations and Kirchhoff checks. Simplify–analyze–expand is a teaching strategy for reducible networks, not a rule that every network must reduce.
✓ Crest’s Checklist
- I combine only true series or parallel groups.
- I recover the p.d. across a parallel group.
- I distinguish source and branch currents.
- I check loop voltage and junction current balances.
- I distinguish open removal from a short.
- I recognize limits of series/parallel reduction.
— Crest ☆ “Simplify valid groups, analyze the whole and expand back to branch quantities.”
Mission 10.9 Complete! · All 10 levels cleared · PHYSICS CREST
★ Combination Circuits Master
An equivalent resistor preserves terminal behavior, while expansion recovers the original internal quantities.