WONDER — The Mystery
Mechanical Work Can Drive a Circuit
A conducting rod slides along rails in a steady magnetic field. A closed resistive loop can carry current without a battery because an external agent supplies mechanical energy. The voltage sign follows the geometry, and a rod can keep moving after you stop pushing.
Model: The motional contribution along a conductor is ∫(v × B)·dl. Magnitude Bℓv applies when a straight rod, its velocity and uniform B are mutually perpendicular. Motion perpendicular to B alone is insufficient: the rod orientation matters. The changing-flux law for a moving circuit is consistent with this motional contribution.
PREDICT — Commit to Your Answer
DOK 2 — PredictA vertical rod moves right in a field out of the page. Which end becomes positive in open-circuit charge equilibrium?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Rightward +x crossed with out-of-page +z gives −y, downward. Electron redistribution leaves the bottom positive and top negative.
▶ PLAY — A Sliding Rod with Correct Polarity and Power
DOK 2 — InvestigatePredict, measure and compare
Compare two speeds at fixed field, then two fields at fixed speed. Reverse either direction, test zero speed or field and open the resistor branch. Watch actual position and circuit current direction.
An ideal vertical conducting rod of length ℓ slides with prescribed signed velocity v along horizontal rails in uniform signed Bz. Positive B is out of the page. The loop closes through total resistance R = 2.0 Ω on the left; rail and rod resistance and self-inductance are negligible. Positive circulation is clockwise, downward through the rod. Signed motional e.m.f. from top to bottom is ε = Bzℓv, I = ε/R when closed, and Fx = −BzℓI. The actuator supplies power −Fx v = I²R; opening the branch gives I = 0 while motional e.m.f. can remain. Rod position x = 0.80 + vt in metres. A 0.20 s physical interval plays over 6 real seconds; dimensions are schematic. Terminal polarity is shown only for nonzero e.m.f. Pause freezes model time, rather than physically removing the prescribed drive.
Status: Ready
Playback: 6 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Geometry, Circuit and Power
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Perpendicular result
Click to flip
Perpendicular result
For a straight rod of length ℓ perpendicular to both uniform B and velocity, e.m.f. magnitude is Bℓv. The general motional contribution is the line integral of v × B along the conductor.
Rule 2
Polarity and charge balance
Click to flip
Polarity and charge balance
For an isolated rod in steady open-circuit equilibrium, E + v × B = 0 along the rod. Positive and negative charge redistribution creates an electric field. In the stated geometry positive B and rightward motion make the bottom end positive.
Rule 3
Closed versus open
Click to flip
Closed versus open
For negligible circuit inductance, closed-loop current is ε/R. The rod force opposes prescribed motion. An open circuit can have e.m.f. and end-to-end voltage but no sustained loop current or the modeled braking force.
Rule 4
Power scales differently
Click to flip
Power scales differently
At fixed B, ℓ and R, doubling speed doubles ε, current and force magnitude, but quadruples heating power ε²/R. Mechanical input power equals electrical dissipation in this ideal constant-speed model.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Motional e.m.f. requires B to change with time.”
Correct — the claim is false.
False. Motion can change loop area and flux in a steady field; v × B can drive charge separation.
Myth 2: “Doubling rod speed doubles resistive heating power.”
Correct — the claim is false.
False at fixed geometry and resistance. E.m.f. doubles, so ε²/R quadruples.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Vector Geometry and Energy
DOK 2 — ApplyUse the mutually perpendicular rod model only under its stated conditions.
Instructor Q1 — Rod Orientation
A rod moves parallel to its own length, with v perpendicular to B. Its motional contribution along the rod is:
Instructor Q2 — Open Branch
The resistor branch is opened while the rod continues moving. The ideal rod can have:
Instructor Q3 — Rod E.m.f.
A 0.30 m rod moves at 2.0 m/s with rod, motion and uniform 0.40 T field mutually perpendicular. Find e.m.f. magnitude.
Instructor Q4 — Heating Power
A closed resistive loop has e.m.f. magnitude 0.80 V and total resistance 4.0 Ω. Find heating power.
4/4 — Instructor Questions Completed
Motional induction is consistent with the moving-loop flux law; a steady B does not imply steady flux through a changing loop.
✎ PRACTICE — Independent Rod-and-Rail Audits
DOK 1–3 — PracticeChallenge 1: Motional E.m.f.
A vertical 0.25 m rod moves right at 3.0 m/s in a uniform 0.60 T field out of the page. Rod, motion and field are mutually perpendicular. Find the signed motional e.m.f. measured from top to bottom.
Step-by-Step Solution
v × B points down; εtop→bottom = +0.60×0.25×3.0 = +0.450 V.
Challenge 2: Force and Heating
A vertical rod of length 0.40 m moves right at 1.5 m/s on rails, in uniform B = 0.50 T out of the page. A resistor on the left closes the loop, with total R = 3.0 Ω and negligible inductance. Find current magnitude, braking-force magnitude and heating power.
Step-by-Step Solution
ε = 0.50×0.40×1.5 = 0.30 V; I = 0.10 A; F = 0.50×0.40×0.10 = 0.020 N; P = I²R = 0.030 W = Fv.
Challenge 3: Audit a Speed-Doubling Report
A vertical 0.20 m rod moves right at 4.0 m/s in a uniform 0.30 T field out of the page. A left resistor closes the rails; total R = 2.0 Ω, with negligible inductance. Find heating power and its value when speed doubles. A report places positive charge at the top, says doubling speed only doubles heating, and says opening the circuit leaves the same braking force. Correct all three claims and identify the energy source needed to maintain speed.
Explanation checks are indicative. Compare your reasoning with the worked solution or your teacher.
Step-by-Step Solution
ε = 0.24 V; I = 0.12 A; P = 0.24²/2 = 0.0288 W. At double speed ε = 0.48 V and P = 0.1152 W. Positive charge is driven downward, leaving the bottom positive. Power quadruples at fixed R. Opening the circuit removes the sustained current and braking force in this ideal model, although e.m.f. persists. External mechanical work supplies the heat.
☷ CHALLENGE — Which Quantity Changes?
DOK 2 — ApplyWhich Quantity Changes?
Select each statement and place it in its matching category. Judge the physical conditions.
0 / 6 correct
Physics Insight
Motional induction is consistent with the moving-loop flux law; a steady B does not imply steady flux through a changing loop.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain v × B polarity, perpendicular geometry, the moving-loop flux change, open and closed circuits, braking force and energy conservation.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 11.14 — Motional E.m.f.
Reach the Peak of Understanding
1. Perpendicular result
For a straight rod of length ℓ perpendicular to both uniform B and velocity, e.m.f. magnitude is Bℓv. The general motional contribution is the line integral of v × B along the conductor.
2. Polarity and charge balance
For an isolated rod in steady open-circuit equilibrium, E + v × B = 0 along the rod. Positive and negative charge redistribution creates an electric field. In the stated geometry positive B and rightward motion make the bottom end positive.
3. Closed versus open
For negligible circuit inductance, closed-loop current is ε/R. The rod force opposes prescribed motion. An open circuit can have e.m.f. and end-to-end voltage but no sustained loop current or the modeled braking force.
4. Power scales differently
At fixed B, ℓ and R, doubling speed doubles ε, current and force magnitude, but quadruples heating power ε²/R. Mechanical input power equals electrical dissipation in this ideal constant-speed model.
5. Moving circuits and Faraday
For a moving closed loop, ε = −dΦ/dt includes changing boundary geometry. A stationary loop in time-varying B and a moving loop in steady B are two induction situations; neither should be excluded from the general flux law.
6. Guitar pickup correction
A conventional magnetic guitar pickup detects a vibrating ferromagnetic string by changing magnetic flux through its stationary coil. It should not be described as directly collecting Bℓv from the string ends. Supporting primary reference: Fender’s guide to single-coil Stratocaster pickups, fender.com/articles/instruments/a-guide-to-fender-single-coil-stratocaster-pickups.
Worked independent practice
C1: +0.450 V. C2: 0.100 A, 0.0200 N and 0.0300 W. C3: 0.0288 W and 0.1152 W; bottom positive, power quadruples, opening removes braking and the actuator supplies energy.
Live investigation and access
An ideal vertical conducting rod of length ℓ slides with prescribed signed velocity v along horizontal rails in uniform signed Bz. Positive B is out of the page. The loop closes through total resistance R = 2.0 Ω on the left; rail and rod resistance and self-inductance are negligible. Positive circulation is clockwise, downward through the rod. Signed motional e.m.f. from top to bottom is ε = Bzℓv, I = ε/R when closed, and Fx = −BzℓI. The actuator supplies power −Fx v = I²R; opening the branch gives I = 0 while motional e.m.f. can remain. Rod position x = 0.80 + vt in metres. A 0.20 s physical interval plays over 6 real seconds; dimensions are schematic. Terminal polarity is shown only for nonzero e.m.f. Pause freezes model time, rather than physically removing the prescribed drive.
Run, Pause, Step and Reset work offline. Complete three matched measurements. Loading a preset is not completing a trial. Saved progress resumes paused. Reduced-motion Run gives a final snapshot; Step allows deliberate inspection. Hints and solutions require a genuine unsuccessful numerical attempt and never complete a task. Explanation rubrics are indicative; compare your physics with the solution or a teacher. Teaching submission checks effort rather than certifying scientific accuracy.
Course scope
The rod-on-rails derived relation is explicit in AP Physics 2 12.4; it is a derived application of electromagnetic induction in A Level 9702 20.5. Detailed charge equilibrium and force/power checks support the ideal model.
Sources: Cambridge International 9702 syllabus ; College Board AP Physics 2 CED. Detailed extension models are labelled in the mission.
✓ Crest’s Checklist
- I state rod and velocity orientations.
- I check polarity with v × B.
- I distinguish e.m.f. and current.
- I use total resistance.
- I check Fv = I²R.
— Crest ☆ “Reach the Peak of Understanding”
Mission 11.14 Complete! · All 10 levels cleared · PHYSICS CREST
★ Motional E.m.f. Investigator
Motional induction is consistent with the moving-loop flux law; a steady B does not imply steady flux through a changing loop.