WONDER — The Mystery
Changing Current and Magnetic Linkage
A changing transmitter current can induce e.m.f. in a separate receiver coil. A receiving current also needs a closed circuit. The same circuit can induce e.m.f. through its own changing flux linkage: self-inductance. Neither effect requires an iron core.
Model: For a linear inductor with constant L, flux linkage λ = LI and self-induced e.m.f. ε = −L dI/dt in the chosen positive circulation. The passive terminal voltage is v = L dI/dt. For two reciprocal linear coils, mutual linkage is M I1 and |M| ≤ √(L1L2). A changing linkage induces e.m.f.; an open receiving winding has no load current.
PREDICT — Commit to Your Answer
DOK 2 — PredictA changing transmitter current links magnetic flux through an open receiver winding. What can occur in the ideal receiver?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Changing linked flux induces e.m.f. The ideal open winding carries no load current. Practical stray capacitance and measuring circuits require a more detailed model.
▶ PLAY — Current Ramp: Self and Mutual Induction
DOK 2 — InvestigatePredict, measure and compare
Compare current-change rates at fixed geometry and coupling, then coupling coefficients at fixed current ramp. Watch current markers and stored field energy. Test zero slope, zero coupling and doubled turns.
Linear quasistatic coupled-coil model with an ideal programmable source imposing I1 = 4 + a t A over 0.50 s. Receiver is open, I2 = 0. Primary is an ideal long air-core solenoid: length 0.50 m, area 1.0×10⁻⁴ m², N variable; μ0 ≈ 4π×10⁻⁷ H/m. L1 = μ0 N²A/length. Receiver self-inductance L2 = 1.0 mH. Coupling coefficient k lies from 0 to 1; M = k√(L1L2), so mutual inductance stays physically bounded. Positive linkage conventions give λ1 = L1 I1, λ2 = M I1; induced circulation e.m.f.s ε1 = −L1 a and ε2 = −M a. Source passive terminal voltage is L1 a. Field energy U = ½L1 I1², and source net work since t = 0 is U − U0; a falling current returns energy to the ideal source. Half a physical second plays over six real seconds. Markers show primary conventional current with schematic speed proportional to I1, not measured carrier drift. The open receiver has no moving current markers. Field-energy bars and current motion represent an actual changing state; connecting curves are linkage symbols, not traveling flux particles. The ramp endpoints are snapshots, not a model of sudden switching.
Status: Ready
Playback: 6 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Linkage, Signs and Stored Energy
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Mutual induction
Click to flip
Mutual induction
With chosen matching flux-linkage conventions and receiver open, ε2 = −M dI1/dt. Terminal polarity depends on reference directions and winding orientation. No wire between windings is necessary; no load current flows in an ideal open receiver.
Rule 2
Self-induced e.m.f. and voltage
Click to flip
Self-induced e.m.f. and voltage
Self-induced ε = −L dI/dt opposes the current change. Passive terminal voltage v = L dI/dt supplies the opposing e.m.f. An inductor opposes changes in current, not current itself. Steady current can produce nonzero flux and stored energy with zero self-induced e.m.f.
Rule 3
Geometry and physical bounds
Click to flip
Geometry and physical bounds
For an ideal long air-core solenoid, L = μ0 N²A/length at fixed geometry. Coil separation, orientation, turns, cores and geometry affect M; simple monotonic claims need geometry conditions. Reciprocal passive linear coils obey |M| ≤ √(L1L2), with k = |M|/√(L1L2) between zero and one.
Rule 4
Field energy and real coils
Click to flip
Field energy and real coils
An ideal linear inductor stores U = ½LI². It returns energy as current falls; it does not dissipate average sinusoidal power like a resistor. Real coils have winding resistance, parasitic capacitance, losses and possibly nonlinear/saturating cores.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Mutual induction requires a wire connecting the windings.”
Correct — the claim is false.
False. Changing magnetic linkage can induce e.m.f. between separate windings. Useful receiving load power also needs a closed receiving circuit.
Myth 2: “An air-core coil has no self-inductance.”
Correct — the claim is false.
False. A current path can link its own magnetic field. Ferromagnetic material can increase inductance under suitable conditions but is not required.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Changing Current and Field Energy
DOK 2 — ApplyUse linear constant inductances and distinguish magnitudes from signed quantities.
Instructor Q1 — Steady Current
An ideal inductor carries constant nonzero current. Which is correct?
Instructor Q2 — Uncoupled Windings
For k = 0 and a changing primary current, the mutual contribution to receiver e.m.f. is:
Instructor Q3 — Receiver E.m.f. Magnitude
Two linear coils have M = 0.030 H. Transmitter current rises at 4.0 A/s; receiver is open. Find induced e.m.f. magnitude.
Instructor Q4 — Stored Field Energy
A linear ideal inductor has L = 0.080 H and carries 3.0 A. Find stored magnetic energy.
4/4 — Instructor Questions Completed
Zero current slope means zero induced e.m.f., not zero magnetic linkage or zero stored energy.
✎ PRACTICE — Independent Inductance Investigations
DOK 1–3 — PracticeChallenge 1: Signed Self-Induction
A linear inductor has L = 0.015 H. Current in its chosen positive circulation increases at 0.20 A/s. Find the signed self-induced e.m.f. in that same circulation.
Step-by-Step Solution
ε = −.015×.20 = −.0030 V.
Challenge 2: Two Coils: Coupling and Energy
Reciprocal linear coils have L1 = 0.020 H, L2 = 0.080 H and coupling coefficient k = 0.50. Receiver is open. Primary current rises at 3.0 A/s. Find mutual inductance, induced receiver e.m.f. magnitude and primary field energy when I1 = 2.0 A.
Step-by-Step Solution
M = .50√(.020×.080) = .020 H; |ε2| = .020×3 = .060 V; U = ½×.020×2² = .040 J.
Challenge 3: Audit an Impossible Coupling Claim
A report gives L1 = 4.0 mH, L2 = 9.0 mH and M = 8.0 mH for reciprocal passive linear coils. Receiver is open. Check whether the stated mutual inductance is possible and calculate the largest allowed magnitude. A revised setup uses k = 0.50 and primary current slope 2.0 A/s; find receiver e.m.f. magnitude. Explain why induced e.m.f. does not mean the open receiver supplies load power, and whether steady nonzero primary current must have zero magnetic energy.
Explanation checks are indicative. Compare your reasoning with the worked solution or your teacher.
Step-by-Step Solution
The bound is √(.004×.009) = .0060 H, so 8.0 mH is impossible in this model. Revised M = .50×.006 = .0030 H; |ε2| = .003×2 = .0060 V. An open receiver has no load current and supplies no load power. Steady primary current can store nonzero ½L1I1² energy while producing zero self-induced e.m.f.
☷ CHALLENGE — Inductance Conditions
DOK 2 — ApplyInductance Conditions
Select each statement and place it in its matching category. Judge the physical conditions.
0 / 6 correct
Physics Insight
Zero current slope means zero induced e.m.f., not zero magnetic linkage or zero stored energy.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain self and mutual induction, a physically bounded coupling coefficient, open versus closed receiving circuits, current-change opposition, stored energy and practical limits.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 11.19 — Mutual and Self-Inductance
Reach the Peak of Understanding
1. Mutual induction
With chosen matching flux-linkage conventions and receiver open, ε2 = −M dI1/dt. Terminal polarity depends on reference directions and winding orientation. No wire between windings is necessary; no load current flows in an ideal open receiver.
2. Self-induced e.m.f. and voltage
Self-induced ε = −L dI/dt opposes the current change. Passive terminal voltage v = L dI/dt supplies the opposing e.m.f. An inductor opposes changes in current, not current itself. Steady current can produce nonzero flux and stored energy with zero self-induced e.m.f.
3. Geometry and physical bounds
For an ideal long air-core solenoid, L = μ0 N²A/length at fixed geometry. Coil separation, orientation, turns, cores and geometry affect M; simple monotonic claims need geometry conditions. Reciprocal passive linear coils obey |M| ≤ √(L1L2), with k = |M|/√(L1L2) between zero and one.
4. Field energy and real coils
An ideal linear inductor stores U = ½LI². It returns energy as current falls; it does not dissipate average sinusoidal power like a resistor. Real coils have winding resistance, parasitic capacitance, losses and possibly nonlinear/saturating cores.
5. Wireless-power applications
Near-field inductive charging uses a time-varying transmitter field linked with a receiver. Rectification and charge-control electronics adapt received power for a battery; an AC coil is not connected directly as a complete battery charger. Coupling depends on dimensions, alignment, separation, frequency and circuit design. Near-field and far-field RFID systems use different mechanisms.
6. AC reactance
For an ideal linear inductor under sinusoidal steady conditions, XL = ωL and current lags its passive terminal voltage by a quarter-cycle. This reactance is not winding resistance or average resistive dissipation. The simple constant-L energy expression needs qualification for nonlinear cores.
Worked independent practice
C1: −.0030 V. C2: .020 H, .060 V and .040 J. C3: maximum .0060 H; revised receiver magnitude .0060 V; the original M is impossible, and open receiver e.m.f. alone delivers no load power.
Live investigation and access
Linear quasistatic coupled-coil model with an ideal programmable source imposing I1 = 4 + a t A over 0.50 s. Receiver is open, I2 = 0. Primary is an ideal long air-core solenoid: length 0.50 m, area 1.0×10⁻⁴ m², N variable; μ0 ≈ 4π×10⁻⁷ H/m. L1 = μ0 N²A/length. Receiver self-inductance L2 = 1.0 mH. Coupling coefficient k lies from 0 to 1; M = k√(L1L2), so mutual inductance stays physically bounded. Positive linkage conventions give λ1 = L1 I1, λ2 = M I1; induced circulation e.m.f.s ε1 = −L1 a and ε2 = −M a. Source passive terminal voltage is L1 a. Field energy U = ½L1 I1², and source net work since t = 0 is U − U0; a falling current returns energy to the ideal source. Half a physical second plays over six real seconds. Markers show primary conventional current with schematic speed proportional to I1, not measured carrier drift. The open receiver has no moving current markers. Field-energy bars and current motion represent an actual changing state; connecting curves are linkage symbols, not traveling flux particles. The ramp endpoints are snapshots, not a model of sudden switching.
Run, Pause, Step and Reset work offline. Complete three matched measurements. Loading a preset is not completing a trial. Saved progress resumes paused. Reduced-motion Run gives a final snapshot; Step allows deliberate inspection. Hints and solutions require a genuine unsuccessful numerical attempt and never complete a task. Explanation rubrics are indicative; compare your physics with the solution or a teacher. Teaching submission checks effort rather than certifying scientific accuracy.
Course scope
Self-inductance, mutual-inductance coefficients and inductor circuits are declared enrichment beyond the separately listed requirements in the current A Level 9702 and AP Physics 2 frameworks. Faraday and Lenz induction supply the foundation.
Sources: Cambridge International 9702 syllabus ; College Board AP Physics 2 CED. Detailed extension models are labelled in the mission.
✓ Crest’s Checklist
- I distinguish self and mutual linkage.
- I state signs or magnitudes explicitly.
- I distinguish terminal voltage from induced circulation e.m.f.
- I check the mutual-inductance bound.
- I distinguish steady current from zero stored energy.
— Crest ☆ “Reach the Peak of Understanding”
Mission 11.19 Complete! · All 10 levels cleared · PHYSICS CREST
★ Mutual and Self-Inductance Investigator
Zero current slope means zero induced e.m.f., not zero magnetic linkage or zero stored energy.