WONDER — The Mystery
Why does one glass respond strongly to a tone?
A tap excites the glass’s free vibration modes. A nearby periodic sound can drive a mode; its response depends on frequency, coupling and energy loss. Similar-looking glasses need not have the same modes. A large response is not guaranteed to break the glass.
Model: Use one linear mechanical mode as an analogue of resonance. Actual glasses have several deformation modes; the moving mass is not the glass’s rigid-body motion or an air particle.
PREDICT — Commit to Your Answer
DOK 2 — PredictFor one lightly damped mode, keep the driving-force amplitude and damping unchanged. Moving the drive frequency from far below to near the natural frequency usually makes its settled displacement amplitude:
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
A lightly damped mode usually has a large response near its natural frequency. Damping limits the settled amplitude; finite-time motion also includes transients. Exact fixed-force displacement peak frequency can be slightly lower than the undamped natural frequency.
▶ PLAY — A Moving Mode with Force and Damping
DOK 2 — InvestigatePredict, measure and compare
Run setups 1, 2 and 3. Compare frequency while holding damping, force and initial displacement fixed; then compare damping while holding the other quantities fixed. Extra setups show free decay, undamped growth and critical damping.
Extension model: m x″ + b x′ + kx = F₀ cos(2πf_drive t), with m = 1 kg, k = 16 N/m, b = 2ζ√(mk), initial x set by the control and v(0) = 0. Natural frequency is √(k/m)/(2π). A 12 s physical run plays in 6 real seconds; Step advances .075 s. The mass position and history follow the exact initial-value solution, including light, critical and heavy damping. Mass displacement uses 800 pixels/m; the history uses 240 pixels/m and force arrows 450 pixels/N. This deliberately slow analogue has no audio, nonlinear glass deformation or fracture model.
Status: Ready
Playback: 6 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Free, Forced and Damped
DOK 1 — RecallFlip all four rule cards. Keep the quantities and model conditions clear.
Rule 1
Free vibration
Click to flip
Free vibration
After a disturbance, a system vibrates in its natural modes without continuing periodic driving. For an ideal undamped spring mode, f₀ = √(k/m)/(2π). Energy is ½mv² + ½kx²; at a turning point it is ½kA² (extension).
Rule 2
Forced motion and energy
Click to flip
Forced motion and energy
A periodic force produces a driven component at the driver’s frequency. Initial free motion can coexist as a transient. Damping removes energy; settled driven motion needs average input to balance average loss. Instantaneous input power is Fv, not force times displacement.
Rule 3
Resonance and damping
Click to flip
Resonance and damping
For light damping, the largest displacement response lies near the natural frequency. At fixed sinusoidal force, A = F₀ / √[(k − mω²)² + (bω)²]. Its interior peak is f₀√(1 − 2ζ²) for 0 < ζ < 1/√2 (extension); heavier damping has no interior displacement peak. Undamped resonant motion grows with time rather than becoming infinite instantly.
Rule 4
Changing natural modes
Click to flip
Changing natural modes
For an ideal stretched string with fixed ends, f₁ = (1/2L)√(T/μ); compare one variable at a time. Longer L or greater mass per length μ lowers f₁, while larger tension T raises it. Rods and glasses have different stiffness and geometry: “thicker always lowers frequency” is not a general rule.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: A resonant response must become infinite as soon as the forcing frequency matches the natural frequency.
Correct — the claim is false.
Real losses and nonlinear effects limit responses. Even an ideal undamped linear oscillator at exact resonance has finite displacement at every finite time; its oscillation envelope grows over time.
Myth 2: If a damped object is driven steadily, its settled oscillation must always have its free natural frequency.
Correct — the claim is false.
Once transients have decayed, a linear oscillator driven by one sinusoidal force oscillates at the forcing frequency. Natural modes govern its response amplitude and phase, and its free response.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Separate the Rate from the Response
DOK 2 — ApplyAnswer the conceptual questions and two connected calculations. Keep the stated string conditions fixed.
Instructor Q1 — Settled rate
A damped mode with undamped natural frequency 300 Hz is driven by a 280 Hz sinusoidal force. After free transients fade, its driven oscillation frequency is:
Instructor Q2 — Controlled scan
To compare displacement amplitudes across drive frequencies, which procedure gives a fair scan?
Instructor Q3 — Free Period
One undamped mode has a period of .00400 s. Find its natural frequency.
Instructor Q4 — String Tension
An ideal string with fixed length and mass per length has a 180 Hz fundamental. Tension is multiplied by four. Find the new fundamental.
4/4 — Instructor Questions Completed
Separate the natural mode, driver frequency and transient motion. Compare resonance responses at fixed driving force and damping, and distinguish a sampled maximum from the true peak.
✎ PRACTICE — Independent Mode and Resonance Investigations
DOK 1–3 — PracticeChallenge 1: Measure a Free Mode
An undamped mechanical mode completes one cycle in .00250 s after a brief disturbance. Find its natural frequency.
Step-by-Step Solution
Natural frequency = 1/.00250 = 400 Hz.
Challenge 2: Retune a Stretched String
An ideal string fixed at both ends has vibrating length .640 m, mass per unit length .00400 kg/m, and tension 102.4 N. Find its fundamental frequency. Then shorten its vibrating length to .400 m, keeping tension and mass per unit length unchanged, and find the new fundamental.
Step-by-Step Solution
Wave speed = √(102.4/.00400) = 160 m/s. Original f₁ = 160/(2 × .640) = 125 Hz. Shortened f₁ = 160/(2 × .400) = 200 Hz.
Challenge 3: Audit a Resonance Scan
For one linear spring mode, stiffness is 800 N/m. At fixed sinusoidal-force amplitude and damping, measured settled displacement amplitudes are .00230 m at 90 Hz, .00460 m at 100 Hz and .00340 m at 110 Hz. Find spring energy at the 100 Hz turning point, its ratio to spring energy at the 90 Hz turning point, and the settled oscillation period in the 110 Hz trial. Select the strongest tested response and propose a controlled follow-up that better locates the peak. A report says these three samples prove the exact peak is 100 Hz, settled motion always follows the natural frequency, an undamped resonant system becomes infinite instantly, and forcing adds energy only when force is in phase with displacement. Correct all four claims. Spring-energy calculations are extension.
Explanation checks are indicative. Compare your reasoning with the worked solution or your teacher.
Step-by-Step Solution
Spring energy = ½ × 800 × .00460² = .008464 J. Ratio = (.00460/.00230)² = 4. Settled period = 1/110 = .00909091 s. The strongest tested response is 100 Hz; scan more closely between 90 and 110 Hz with the same force amplitude and damping and allow settling, including repeat measurements. Three samples do not locate an exact peak. Settled driven motion follows the driver, not necessarily the free natural frequency. Ideal undamped resonant growth is finite at finite time. Input power is Fv: force aligned with velocity adds energy; force aligned with displacement alone does not establish positive input.
☷ CHALLENGE — Classify the Oscillation Evidence
DOK 2 — ApplyClassify the Oscillation Evidence
Select each statement and place it in its matching category. Judge the physical conditions.
0 / 6 correct
Physics Insight
Separate the natural mode, driver frequency and transient motion. Compare resonance responses at fixed driving force and damping, and distinguish a sampled maximum from the true peak.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain free modes, forced motion, resonance and damping using a glass or a swing. State what you keep fixed in a fair comparison.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 13.7 — Natural Vibration and Resonance
Reach the Peak of Understanding
1. Free vibration
After a disturbance, a system vibrates in its natural modes without continuing periodic driving. For an ideal undamped spring mode, f₀ = √(k/m)/(2π). Energy is ½mv² + ½kx²; at a turning point it is ½kA² (extension).
2. Forced motion and energy
A periodic force produces a driven component at the driver’s frequency. Initial free motion can coexist as a transient. Damping removes energy; settled driven motion needs average input to balance average loss. Instantaneous input power is Fv, not force times displacement.
3. Resonance and damping
For light damping, the largest displacement response lies near the natural frequency. At fixed sinusoidal force, A = F₀ / √[(k − mω²)² + (bω)²]. Its interior peak is f₀√(1 − 2ζ²) for 0 < ζ < 1/√2 (extension); heavier damping has no interior displacement peak. Undamped resonant motion grows with time rather than becoming infinite instantly.
4. Changing natural modes
For an ideal stretched string with fixed ends, f₁ = (1/2L)√(T/μ); compare one variable at a time. Longer L or greater mass per length μ lowers f₁, while larger tension T raises it. Rods and glasses have different stiffness and geometry: “thicker always lowers frequency” is not a general rule.
Worked independent practice
C1: 400 Hz. C2: 125 Hz then 200 Hz. C3: .008464 J, ratio 4, period .00909091 s; 100 Hz is the strongest sampled response, requiring a finer controlled scan and four corrected report claims.
Live investigation and access
Extension model: m x″ + b x′ + kx = F₀ cos(2πf_drive t), with m = 1 kg, k = 16 N/m, b = 2ζ√(mk), initial x set by the control and v(0) = 0. Natural frequency is √(k/m)/(2π). A 12 s physical run plays in 6 real seconds; Step advances .075 s. The mass position and history follow the exact initial-value solution, including light, critical and heavy damping. Mass displacement uses 800 pixels/m; the history uses 240 pixels/m and force arrows 450 pixels/N. This deliberately slow analogue has no audio, nonlinear glass deformation or fracture model.
Run, Pause, Step and Reset work offline. Complete three matched measurements. Loading a preset is not completing a trial. Saved progress resumes paused. Reduced-motion Run gives a final snapshot; Step allows deliberate inspection. Hints and solutions require a genuine unsuccessful numerical attempt and never complete a task. Explanation rubrics are indicative; compare your physics with the solution or a teacher. Teaching submission checks effort rather than certifying scientific accuracy.
Course scope
Cambridge A Level 9702 17.1–17.3 covers free oscillations, damping, forced oscillations and resonance. Cambridge AS wave work supports period and string-wave connections; the quantitative damped-oscillator solver and displacement-peak shift are extension. AP Physics 2 14.6 provides standing-wave and mode connections; detailed spring damping and resonance scans are enrichment.
Sources: Cambridge International 9702 syllabus ; College Board AP Physics 2 CED. Detailed extension models are labelled in the mission.
✓ Crest’s Checklist
- I separate free and driven frequencies.
- I distinguish transients from settled motion.
- I connect driving and damping to energy transfer.
- I qualify displacement resonance and finite-time growth.
- I change string variables under stated conditions.
— Crest ☆ “Reach the Peak of Understanding”
Mission 13.7 Complete! · All 10 levels cleared · PHYSICS CREST
★ Natural Vibration and Resonance Investigator
Separate the natural mode, driver frequency and transient motion. Compare resonance responses at fixed driving force and damping, and distinguish a sampled maximum from the true peak.