Skip to lesson
PCPHYSICS CREST
1

Topic 14 · Temperature

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

Cambridge International A Level Physics 9702

The whole topic in one idea: temperature predicts the direction of net energy transfer; calorimetry measures how supplied energy changes temperature or state.

Exact syllabus boundary
14.1 thermal equilibrium; 14.2 temperature scales and thermometry; 14.3 specific heat capacity and specific latent heat. Molecular internal-energy bookkeeping and the first law belong to Topic 16.

14.1 · Thermal equilibrium

  • Temperature characterises thermal equilibrium and the direction of net thermal energy transfer.
  • Internal energyA property of a system, not simply another name for temperature.
  • A phase change can increase internal energy without raising temperature.
Two bodies are in thermal equilibrium when they have the same temperature and there is no net energy transfer between them.
Energy transfer toward thermal equilibriumA hotter body transfers energy to a cooler body until both reach one final temperature and there is no net energy transfer.higher temperaturelower temperaturenet energy transferat equilibrium: same temperature, no net transfer
Direction rule
When systems interact thermally, net energy transfer is from the higher-temperature system to the lower-temperature system until their temperatures become equal.
Common mistake
Equal temperature does not mean equal internal energy. Bodies may contain different amounts or kinds of material. Temperature—not mass or total stored energy—sets the initial transfer direction.
Quick Check 1
A small hot metal block touches a large warm block. Which way is the initial net transfer?
From the hotter block to the cooler block, regardless of which has the greater mass.
2

Thermometric properties

A thermometric property is a measurable physical property that changes reproducibly with temperature.
InstrumentThermometric propertyUseful feature
liquid-in-glassliquid-column lengthsimple visual reading
resistance thermometerelectrical resistancewide range and remote sensing
thermocouplethermoelectric e.m.f.small, fast response
constant-volume gas thermometergas pressureapproaches thermodynamic scale at low density
Calibrating a thermometric propertyA graph shows property X at the ice point and steam point. An unknown temperature is found by interpolation only if the property is assumed linear.0 °C100 °CθXlinear calibration assumption
$θ=100(X_θ-X_0)/(X_{100}-X_0)$ °C   (only when $X$ is assumed linear with Celsius temperature)
Exam trap
Two thermometers calibrated at 0 °C and 100 °C can disagree between the fixed points if their properties do not vary in the same way. Never assume linearity unless the model, graph or question permits it.

Choosing an instrument

  • Choose a thermometer using its measurable property, range and response.
  • In calorimetry, distinguish heater input from energy actually gained by the sample.
  • Heat capacity and specific heat capacity differ by the mass factor.

Link the choice to the context: range, sensitivity, response time, size, robustness, remote output and whether the property is sufficiently linear.

3

Thermodynamic temperature scale

The thermodynamic temperature scale is independent of the thermometric property of any particular substance.
$T/\mathrm K=θ/^\circ\mathrm C+273.15$
Convert a temperature
25.0 °C = 298.15 K, normally reported as 298 K to three significant figures.
Convert an interval
A rise of 18.0 °C is a rise of 18.0 K. Temperature intervals have the same numerical size.
Absolute zero
0 K = −273.15 °C. Kelvin temperatures are never written with a degree symbol. Use kelvin in gas equations.
Common mistake
Do not add 273.15 to a temperature difference. Add it only when converting an actual Celsius temperature to an actual thermodynamic temperature.
Quick Check 2
A sample warms from 12 °C to 47 °C. What is $ΔT$?
$ΔT=35$ °C = 35 K.
4

Specific heat capacity & energy balance

Specific heat capacity $c$ is the energy required per unit mass to raise the temperature of a substance by one kelvin, without a change of state.
$Q=mcΔT$    unit of $c$: J kg−1 K−1

The energy-ledger method

  1. Choose the complete system.
  2. For every body that changes temperature, write $mc(T_f-T_i)$.
  3. Write energy gained as positive and energy lost as negative, or equate loss magnitudes to gain magnitudes.
  4. Include the container or heater when its heat capacity is given.
  5. Check that $T_f$ lies between the initial temperatures for an isolated mixing problem with no phase change.
Worked mixing example
0.200 kg of water at 80.0 °C mixes with 0.300 kg at 20.0 °C. Neglect losses. Because both have the same $c$, $0.200(80-T_f)=0.300(T_f-20)$, giving $T_f=44.0$ °C.
Exam trap
Do not use the same $ΔT$ for every object in a mixing calculation. Each term needs its own initial temperature and the common final temperature.
Your turn · Find energy for m = 0.50 kg, c = 800 J/(kg K), ΔT = 6.0 K.

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

5

Measuring specific heat capacity

Specific heat capacity · electrical heating methodSpecific heat capacity · electrical heating methodinsulated block, mass mheatercurrent-limitedlow-V supplyAVthermometerMeasure I, V, t and ΔT.

Electrical method

$E=VIt=Pt,\qquad c=E/(mΔT)$

Measure mass, potential difference, current, heating time and temperature. Improve thermal contact with oil in the sensor/heater holes; insulate the block; use a lid where appropriate; record temperature continuously.

Graph method

At approximately constant electrical power, a graph of temperature against time has initial gradient $\mathrm dT/\mathrm dt≈P/(mc)$. Hence $c=P/[m(\mathrm dT/\mathrm dt)]$. The earliest gradient reduces the effect of increasing loss to the surroundings.

Cooling correction
Heat loss makes the measured temperature rise too small, so using all electrical energy as $mcΔT$ usually makes calculated $c$ too large. Extrapolation or matched cooling-rate methods can estimate the loss.
LimitationEffectImprovement
energy lost to air$ΔT$ too smallinsulation, lid, shorter run, correction
poor thermal contactsensor lags blockoil and small well-fitting holes
non-uniform temperaturelocal reading not representativestir liquid or use conducting block and wait
6

Specific latent heat & phase changes

Specific latent heat $L$ is the energy required per unit mass to change the state of a substance without changing its temperature.
$Q=mL$    unit of $L$: J kg−1
Heating curve for a pure substanceTemperature rises in single phases and remains constant during ideal melting and boiling plateaus while energy continues to be supplied.meltingboilingenergy supplied / time at constant powertemperature

Fusion

$L_f$ applies to solid ↔ liquid at the melting point.

Vaporisation

$L_v$ applies to liquid ↔ gas at the boiling point.

Multi-stage questions

Split the journey at every phase boundary. Use $mcΔT$ on sloping sections and $mL$ on plateaus, then add the energies.

Worked stage ledger
To take 0.0500 kg of ice at 0 °C to water at 20.0 °C: $Q=mL_f+mc_wΔT$. With $L_f=3.34×10^5$ J kg−1 and $c_w=4200$ J kg−1 K−1, $Q=2.09×10^4$ J.
Common mistake
Temperature remains constant during an ideal phase change even though energy is still transferred. Do not use $mcΔT$ for the plateau.
Explain · During melting at constant temperature, can a substance gain internal energy?

7

Master equation sheet

Why vaporisation usually needs more energy than fusion
For the same substance, $L_v$ is usually greater than $L_f$. During melting, particles lose the ordered solid arrangement but remain close together. During vaporisation, particles become much more widely separated, so substantially more energy is required to overcome attractive interactions. Treat this as a reasoning pattern, not a universal numerical ratio.
Final-check boundary
Topic 14 uses temperature, $Q=mc\Delta T$ and $Q=mL$. The ideal-gas equations belong to Topic 15, while microscopic internal-energy bookkeeping and the first law belong to Topic 16. A Paper 4 question may later combine topics, but these are not extra Topic 14 recall formulae.

Equations and definitions

Celsius–Kelvin$T=θ+273.15$
Linear empirical calibration$θ=100(X-X_0)/(X_{100}-X_0)$
Heating without change of state$Q=mcΔT$
Electrical energy$E=VIt=Pt$
Change of state$Q=mL$
Isolated calorimetrytotal energy lost = total energy gained
Common mistakes
  • equating temperature with total energy
  • assuming every thermometric property is linear
  • using °C in a gas equation
  • omitting the container heat capacity
  • using one $ΔT$ for all bodies
  • using $mcΔT$ during a phase change
Final checklist
  • write the complete energy ledger
  • convert grams to kilograms
  • keep temperature intervals in K or °C consistently
  • include units and sensible significant figures
  • state the direction/effect of heat loss
  • check the final temperature is physically possible