Skip to lesson
1

Topic 21 · Alternating Currents

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

  • Alternating current varies with time and reverses direction.
  • Its mean over a full sinusoidal cycle can be zero while it still heats a resistor.
  • Heating depends on current squared.
Cambridge International A Level Physics 9702

The whole topic in one idea: a sinusoidal quantity reverses direction; r.m.s. values compare its heating effect with d.c.; diodes make a one-polarity output and a capacitor reduces its ripple.

Exact syllabus boundary
21.1 a.c. period, frequency, peak, sinusoidal equations, r.m.s. and mean resistor power; 21.2 half/full-wave rectification and capacitor smoothing. Transformer operation is not a Topic 21 outcome.
Sinusoidal voltage · peak, r.m.s. and periodSinusoidal voltage · peak, r.m.s. and periodV₀Vrms = V₀/√2one period T
$x=x_0\sinωt$,   $ω=2πf=2π/T$

x may be current or voltage. Peak-to-peak value is $2x_0$; peak value is measured from the zero line to one extreme.

Common mistake
The mean value over a complete symmetric cycle is zero, but the r.m.s. value and mean power are not zero.
2

Root-mean-square values

The r.m.s. value of an alternating current/voltage is the value of steady direct current/voltage that produces the same mean heating effect (mean power) in a resistor.
$I_{rms}=I_0/\sqrt2$,   $V_{rms}=V_0/\sqrt2$

Why the square and root?

  • Root-mean-square current is the steady current giving the same mean heating in the same resistor.
  • For a sinusoid, I_rms = I₀/√2.
  • Rectification changes which parts of the waveform reach a load; smoothing reduces voltage variation rather than creating energy.

Heating power is proportional to $I^2$ or $V^2$. Square the alternating values, average over a cycle, then take the square root to recover an equivalent current or voltage.

QuantitySinusoidal relation
peak$x_0=\sqrt2x_{rms}$
peak-to-peak$2x_0=2\sqrt2x_{rms}$
mean over full cyclezero for x, non-zero for x²
Definition trap
Do not define r.m.s. as “the average current”. State equal mean heating effect in a resistor compared with d.c.
Your turn · Find rms voltage for a sinusoid with peak voltage 20√2 V.

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

3

Power in a resistive load

Instantaneous power in a resistorFor sinusoidal voltage and current in phase, instantaneous power is proportional to sine squared, never negative, and has twice the frequency. Its mean is half its maximum.mean = ½ maximumtp

For a resistor, voltage and current are in phase. Instantaneous power is

$p=vi=V_0I_0\sin^2ωt$

Since the mean of $\sin^2$ over a cycle is one half,

$P_{mean}=\tfrac12P_{max}=V_{rms}I_{rms}=I_{rms}^2R=V_{rms}^2/R$
Worked load
A 12.0 V r.m.s. supply across 6.0 Ω gives $P_{mean}=12^2/6=24$ W. Peak instantaneous power is 48 W.
Common mistake
Do not mix peak voltage with r.m.s. current in a power equation. Use both peak values for maximum power or both r.m.s. values for mean power.
Explain · Why can an alternating current with zero mean still heat a resistor?

4

Half-wave rectification

Input, half-wave and full-wave rectificationThe input alternates positive and negative. Half-wave output keeps one half-cycle and is zero for the other. Full-wave output makes both half-cycles the same polarity and doubles the pulse repetition frequency.inputhalffullt

A single diode conducts during one supply half-cycle and blocks during the other. The load current therefore has one polarity but includes zero intervals.

FeatureHalf-wave output
diodesone
conductionone half-cycle only
output pulse repetitionsame frequency as input
unused inputone half-cycle
Graph checklist
Preserve input timing and peak magnitude for ideal diodes. Replace the blocked half-cycle by the zero line; do not reflect it.
5

Full-wave bridge rectification

Full-wave bridge · the load current keeps one directionFull-wave bridge · the load current keeps one directionload+ output− outputa.c.a.c.

Four diodes form a bridge. One diagonal pair conducts in one half-cycle and the other pair in the next. Both routes drive current through the load in the same direction.

FeatureFull-wave bridge
conducting diodestwo per half-cycle
load currentsame direction in both half-cycles
output pulse repetitiontwice input frequency
ideal output magnitudeabsolute value of input
Path trap
Do not memorise diode labels without tracing. Start at the instantaneously positive input terminal, pass through a forward diode, through the load in the required direction, then return through a second forward diode.
6

Capacitor smoothing

Capacitor smoothing · output never exceeds input peakCapacitor smoothing · output never exceeds input peaksmaller RC: larger ripplelarger RC: smaller ripple

Connect the smoothing capacitor in parallel with the load. Near a rectified peak it charges rapidly. Between peaks the supply falls below capacitor voltage, the diodes switch off, and the capacitor discharges through the load.

ChangeEffectReason
larger Cless ripplesame discharged charge gives smaller ΔV=ΔQ/C
larger load Rless ripplesmaller load current; slower discharge
full-wave rather than half-waveless time between peakscapacitor is refreshed twice per input cycle
$\Delta Q\approx I_{load}\Delta t$,   $\Delta V\approx\Delta Q/C$
Common mistake
Smoothing does not produce perfectly constant d.c. The remaining variation is ripple, and the capacitor belongs across the load, not in series.
7

Paper 4 technique & master sheet

Waveform transformation routine

  1. Mark zero, peak, period and polarity of the input.
  2. For each half-cycle, identify which diode route conducts.
  3. Draw the load output with the same time scale.
  4. Add capacitor action: rapid charge near peaks, slower discharge between peaks.
  5. Check output repetition frequency and ripple direction.

Master equations

sinusoid$x=x_0\sinωt$
frequency links$ω=2πf$, $T=1/f$
r.m.s.$I_{rms}=I_0/\sqrt2$, $V_{rms}=V_0/\sqrt2$
mean power$P=V_{rms}I_{rms}=I_{rms}^2R=V_{rms}^2/R$
power maximum$P_{mean}=\tfrac12P_{max}$
smoothing estimate$\Delta Q=I\Delta t$, $\Delta V=\Delta Q/C$
Final traps
  • peak is half peak-to-peak
  • r.m.s. is not the arithmetic mean
  • full-wave pulse frequency is 2f
  • load current keeps one direction in a bridge
  • larger C or R reduces ripple
Boundary
Do not import transformer turns calculations from older topical banks. Electromagnetic induction is Topic 20.