Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.
Evidence-led bank
40 original multiple-choice questions and 10 original structured scenarios cover every Topic 10 learning outcome and the recurring techniques found across the shared electricity papers. The count follows distinct exam skills—not a fixed quota.
Topic boundary
Topic 9 current, p.d., power, resistance and resistivity are used only as prerequisites. Electric fields belong to Topic 18. Named maximum-power and Wheatstone-bridge theorems are not required here.
MCQ progress0 of 40 attempted · 0 correct
Paper 1 · Multiple Choice
Q1 Easy10.1
The diagram represents a cell. Which statement is correct?
A. X is the positive terminal.
B. Y is the positive terminal.
C. X and Y are both negative terminals.
D. The plate lengths do not show polarity.
The longer plate of a cell symbol is the positive terminal. Answer: A.
Q2 Easy10.1
Which arrangement measures the current through a resistor and the p.d. across it correctly?
A. Ammeter in parallel; voltmeter in series
B. Ammeter in series; voltmeter in parallel
C. Both meters in series
D. Both meters in parallel
The ammeter must carry the resistor current, so it is in series. The voltmeter compares the resistor's two terminal potentials, so it is in parallel. Answer: B.
Q3 Medium10.1
Two resistors are connected as shown. How are $R_1$ and $R_2$ connected?
A. In series because they are drawn one above the other
B. In series because current can pass through both
C. In parallel because both ends connect to the same two nodes
D. Neither series nor parallel because the drawing is rectangular
Topology is set by nodes, not by page shape. Each resistor is connected directly between P and Q. Answer: C.
Q4 Easy10.1
Which statement defines the e.m.f. of a source?
A. Force exerted on each coulomb inside the source
B. Charge supplied by the source each second
C. Electrical energy transferred from each coulomb in the external resistor
D. Energy transferred by the source to electrical energy per unit charge around the complete circuit
E.m.f. is an energy-per-charge quantity for the source; it is not a mechanical force. Answer: D.
Q5 Easy10.1
A source transfers $18\,\mathrm J$ of energy to $3.0\,\mathrm C$ of charge. What is its e.m.f.?
A. $6.0\,\mathrm V$
B. $15\,\mathrm V$
C. $21\,\mathrm V$
D. $54\,\mathrm V$
$\varepsilon=W/Q=18/3.0=6.0\,\mathrm{J\,C^{-1}}=6.0\,\mathrm V$. Answer: A.
Q6 Medium10.1
A source of e.m.f. $12.0\,\mathrm V$ and internal resistance $0.80\,\Omega$ supplies current $1.50\,\mathrm A$. What is its terminal p.d.?
A. $9.6\,\mathrm V$
B. $12.0\,\mathrm V$
C. $10.8\,\mathrm V$
D. $13.2\,\mathrm V$
While supplying current, $V=\varepsilon-Ir=12.0-(1.50)(0.80)=10.8\,\mathrm V$. Answer: C.
Q7 Medium10.1
A cell has e.m.f. $9.0\,\mathrm V$ and internal resistance $1.0\,\Omega$. It is connected to a $5.0\,\Omega$ resistor. What current flows?
A. $1.0\,\mathrm A$
B. $1.5\,\mathrm A$
C. $1.8\,\mathrm A$
D. $2.3\,\mathrm A$
The complete-circuit resistance is $R+r=6.0\,\Omega$, so $I=\varepsilon/(R+r)=9.0/6.0=1.5\,\mathrm A$. Answer: B.
Q8 Hard10.1
A source of e.m.f. $9.0\,\mathrm V$ gives terminal p.d. $7.2\,\mathrm V$ when its current is $1.8\,\mathrm A$. What is its internal resistance?
A. $0.20\,\Omega$
B. $0.40\,\Omega$
C. $0.80\,\Omega$
D. $1.0\,\Omega$
Lost volts $=\varepsilon-V=1.8\,\mathrm V$. Hence $r=(\varepsilon-V)/I=1.8/1.8=1.0\,\Omega$. Answer: D.
Q9 Medium10.1
The graph shows terminal p.d. $V$ against current $I$ for a source. What do the intercept and gradient represent?
A. $V$-intercept $=\varepsilon$; gradient $=-r$
B. $V$-intercept $=r$; gradient $=-\varepsilon$
C. $I$-intercept $=r$; gradient $=\varepsilon$
D. $V$-intercept $=\varepsilon-r$; gradient $=+r$
Rearrange the source equation as $V=\varepsilon-rI$, in straight-line form. Answer: A.
Q10 Hard10.1
Two points on a source's $V$–$I$ line are $(0.40\,\mathrm A,5.60\,\mathrm V)$ and $(1.40\,\mathrm A,4.10\,\mathrm V)$. What are $\varepsilon$ and $r$?
A. $\varepsilon=5.0\,\mathrm V$, $r=0.67\,\Omega$
B. $\varepsilon=5.6\,\mathrm V$, $r=1.0\,\Omega$
C. $\varepsilon=6.2\,\mathrm V$, $r=1.5\,\Omega$
D. $\varepsilon=7.1\,\mathrm V$, $r=2.5\,\Omega$
Gradient $=(4.10-5.60)/(1.40-0.40)=-1.50\,\mathrm{V\,A^{-1}}$, so $r=1.50\,\Omega$. Then $\varepsilon=V+Ir=5.60+(0.40)(1.50)=6.20\,\mathrm V$. Answer: C.
Q11 Medium10.1
A high-resistance voltmeter is connected across an isolated cell. Why is its reading approximately the cell's e.m.f.?
A. The voltmeter removes the internal resistance.
B. The current is almost zero, so the lost volts $Ir$ are almost zero.
C. The voltmeter supplies energy to the cell.
D. The e.m.f. becomes equal to the internal resistance.
A very large voltmeter resistance makes $I\approx0$, so $V=\varepsilon-Ir\approx\varepsilon$. Answer: B.
Q12 Hard10.1
A rechargeable cell has e.m.f. $1.50\,\mathrm V$ and internal resistance $0.20\,\Omega$. A charging current of $0.50\,\mathrm A$ enters its positive terminal. What is the terminal p.d.?
A. $0.75\,\mathrm V$
B. $1.40\,\mathrm V$
C. $1.50\,\mathrm V$
D. $1.60\,\mathrm V$
For a cell being charged, the applied terminal p.d. is $V=\varepsilon+Ir=1.50+(0.50)(0.20)=1.60\,\mathrm V$. Answer: D.
Q13 Medium10.1/10.2
Cells of e.m.f. $8.0\,\mathrm V$ and $2.0\,\mathrm V$ oppose one another in a single loop whose total resistance is $3.0\,\Omega$. What is the current?
A. $2.0\,\mathrm A$, driven by the $8.0\,\mathrm V$ cell
B. $2.0\,\mathrm A$, driven by the $2.0\,\mathrm V$ cell
C. $3.3\,\mathrm A$, driven by the $8.0\,\mathrm V$ cell
D. $0\,\mathrm A$ because the cells oppose
The net e.m.f. is $8.0-2.0=6.0\,\mathrm V$, so $I=6.0/3.0=2.0\,\mathrm A$ in the direction driven by the stronger cell. Answer: A.
Q14 Easy10.2
Kirchhoff's first law follows directly from conservation of
A. mass.
B. momentum.
C. charge.
D. electrical resistance.
At a steady-current junction, charge does not accumulate: total current entering equals total current leaving. Answer: C.
Q15 Medium10.2
Currents $1.20\,\mathrm A$ and $0.75\,\mathrm A$ enter a junction. Current $0.48\,\mathrm A$ and current $I$ leave. What is $I$?
A. $0.93\,\mathrm A$
B. $1.47\,\mathrm A$
C. $1.95\,\mathrm A$
D. $2.43\,\mathrm A$
$1.20+0.75=0.48+I$, so $I=1.47\,\mathrm A$. Answer: B.
Q16 Easy10.2
Kirchhoff's second law is a circuit statement of conservation of
A. charge at a junction.
B. current in a resistor.
C. resistance around a loop.
D. energy around a closed loop.
The sum of energy supplied per unit charge equals the sum transferred per unit charge around a closed loop. Answer: D.
Q17 Medium10.2
A branch current is assumed to flow from P to Q. Solving the circuit gives $I=-0.36\,\mathrm A$. What is the physical result?
A. Current $0.36\,\mathrm A$ flows from Q to P.
B. No current flows.
C. Current $-0.36\,\mathrm A$ physically flows from P to Q.
D. The resistance must be negative.
The negative sign means the real direction is opposite to the chosen arrow; the magnitude is $0.36\,\mathrm A$. Answer: A.
Q18 Easy10.2
Resistors $3.0\,\Omega$, $4.0\,\Omega$ and $5.0\,\Omega$ are in series. What is their combined resistance?
A. $1.28\,\Omega$
B. $4.0\,\Omega$
C. $12.0\,\Omega$
D. $60\,\Omega$
The same current passes through series resistors, so their p.d.s add and $R_{\mathrm s}=3.0+4.0+5.0=12.0\,\Omega$. Answer: C.
Q19 Medium10.2
A $6.0\,\Omega$ resistor and a $3.0\,\Omega$ resistor are connected in parallel. What is their combined resistance?
A. $1.0\,\Omega$
B. $2.0\,\Omega$
C. $4.5\,\Omega$
D. $9.0\,\Omega$
$1/R_{\mathrm p}=1/6.0+1/3.0=1/2.0$, so $R_{\mathrm p}=2.0\,\Omega$, smaller than either branch. Answer: B.
Q20 Hard10.2
A $4.0\,\Omega$ resistor and a $6.0\,\Omega$ resistor are in parallel. The total current entering the pair is $5.0\,\mathrm A$. What current flows in the $6.0\,\Omega$ branch?
A. $1.0\,\mathrm A$
B. $1.5\,\mathrm A$
C. $3.0\,\mathrm A$
D. $2.0\,\mathrm A$
$R_{\mathrm p}=2.4\,\Omega$, so the p.d. across the pair is $(5.0)(2.4)=12\,\mathrm V$. Hence $I_{6\Omega}=12/6.0=2.0\,\mathrm A$. Answer: D.
Q21 Medium10.2
A $2.0\,\Omega$ resistor is in series with a parallel combination of $6.0\,\Omega$ and $3.0\,\Omega$. The network is connected to $12\,\mathrm V$. What is the supply current?
A. $3.0\,\mathrm A$
B. $2.0\,\mathrm A$
C. $1.5\,\mathrm A$
D. $1.1\,\mathrm A$
$6.0\,\Omega\parallel3.0\,\Omega=2.0\,\Omega$. Total $R=2.0+2.0=4.0\,\Omega$, so $I=12/4.0=3.0\,\mathrm A$. Answer: A.
Q22 Medium10.2
The switch is initially open. The two resistors are identical and the source is ideal. What happens to the total current when the switch is closed?
A. It halves.
B. It is unchanged.
C. It doubles.
D. It becomes zero.
Closing the switch places a second $R$ in parallel, changing the equivalent resistance from $R$ to $R/2$. At fixed p.d., the total current doubles. Answer: C.
Q23 Hard10.1/10.2
A source has e.m.f. $10.0\,\mathrm V$ and internal resistance $0.50\,\Omega$. It supplies two $6.0\,\Omega$ resistors in parallel. What is the terminal p.d.?
A. $5.00\,\mathrm V$
B. $8.57\,\mathrm V$
C. $9.50\,\mathrm V$
D. $10.0\,\mathrm V$
External $R=3.0\,\Omega$ and total $R=3.50\,\Omega$. Thus $I=10.0/3.50=2.857\,\mathrm A$ and $V=IR_{\mathrm{external}}=(2.857)(3.0)=8.57\,\mathrm V$. Answer: B.
Q24 Medium10.2
A loop is traced across a cell from its negative terminal to its positive terminal and then through a resistor in the chosen current direction. Which signed terms are correct?
A. $-\varepsilon$ and $+IR$
B. $-\varepsilon$ and $-IR$
C. $+\varepsilon$ and $+IR$
D. $+\varepsilon$ and $-IR$
Crossing a source from $-$ to $+$ is a rise $+\varepsilon$; moving through a resistor with current is a drop $-IR$. Answer: D.
Q25 Hard10.2
Two source branches form a closed loop with no external load. One branch contains a $12\,\mathrm V$ source and $3.0\,\Omega$ resistance; the other contains a $6.0\,\mathrm V$ source of the same polarity and $3.0\,\Omega$ resistance. What circulating current flows?
A. $1.0\,\mathrm A$, driven from the stronger source towards the weaker source
B. $2.0\,\mathrm A$, driven from the weaker source towards the stronger source
C. $3.0\,\mathrm A$, with both sources aiding
D. No current because the sources have the same polarity
Around the loop the e.m.f.s oppose: $I=(12-6)/(3.0+3.0)=1.0\,\mathrm A$. The stronger source drives current into the weaker source. Answer: A.
Q26 Hard10.2
A three-branch network gives the equations
$$I_1=I_2+I_3,\qquad 10=2I_1+4I_2,\qquad 4I_2=2+2I_3.$$
What is $I_3$?
A. $0.20\,\mathrm A$
B. $1.0\,\mathrm A$
C. $1.4\,\mathrm A$
D. $2.6\,\mathrm A$
Use $I_3=2I_2-1$ and $I_1=3I_2-1$. Substitution gives $10=2(3I_2-1)+4I_2$, so $I_2=1.2\,\mathrm A$ and $I_3=1.4\,\mathrm A$. Answer: C.
Q27 Easy10.3
A potential divider has $R_1=2.0\,\Omega$ in series above $R_2=4.0\,\Omega$ across $12\,\mathrm V$. The output is across $R_2$. What is $V_{\mathrm{out}}$?
A. $4.0\,\mathrm V$
B. $8.0\,\mathrm V$
C. $12\,\mathrm V$
D. $24\,\mathrm V$
$V_{\mathrm{out}}=12[4.0/(2.0+4.0)]=8.0\,\mathrm V$. The numerator is the resistance directly across the output nodes. Answer: B.
Q28 Medium10.3
Resistors $6.0\,\mathrm{k}\Omega$ and $2.0\,\mathrm{k}\Omega$ form a divider across $10.0\,\mathrm V$. The output is measured across the $6.0\,\mathrm{k}\Omega$ resistor. What is the output?
A. $1.25\,\mathrm V$
B. $2.50\,\mathrm V$
C. $5.00\,\mathrm V$
D. $7.50\,\mathrm V$
$V_{\mathrm{out}}=10.0[6.0/(6.0+2.0)]=7.50\,\mathrm V$. “Upper” or “lower” does not decide the numerator; the output terminals do. Answer: D.
Q29 Hard10.2/10.3
The divider is connected to an $8.0\,\mathrm V$ ideal supply. What is the loaded output p.d.?
A. $4.0\,\mathrm V$
B. $5.33\,\mathrm V$
C. $6.0\,\mathrm V$
D. $8.0\,\mathrm V$
$12\,\mathrm{k}\Omega\parallel6\,\mathrm{k}\Omega=4\,\mathrm{k}\Omega$. The loaded divider is therefore $4\,\mathrm{k}\Omega$ over $4+4\,\mathrm{k}\Omega$, giving $V_{\mathrm{out}}=4.0\,\mathrm V$. Answer: A.
Q30 Medium10.3
An ideal divider's output is first measured with a very high-resistance voltmeter. It is then connected to a load of finite resistance in parallel with the output resistor. What usually happens to the output p.d.?
A. It always becomes equal to the supply p.d.
B. It is unchanged because parallel branches have the same p.d.
C. It decreases because the effective output resistance is reduced.
D. It becomes negative.
The load is in parallel with the output resistor, reducing that part of the divider and normally reducing its fraction of the supply p.d. Answer: C.
Q31 Medium10.3
The output is measured across the LDR. What happens to $V_{\mathrm{out}}$ when the light becomes brighter?
A. It increases.
B. It decreases.
C. It remains exactly constant.
D. It alternates.
Brighter light lowers the LDR resistance. Since $V_{\mathrm{out}}$ is the fraction across the LDR, that fraction decreases. Answer: B.
Q32 Medium10.3
An LDR is the upper resistor of a divider and a fixed resistor is below it. The output is across the fixed resistor. What happens to the output as light intensity increases?
A. It falls to zero in every case.
B. It decreases because the LDR resistance decreases.
C. It is unaffected by the LDR.
D. It increases because the fixed resistor becomes a larger fraction of the total resistance.
The LDR's upper resistance falls. The lower fixed resistance then forms a larger fraction $R_{\mathrm fixed}/(R_{\mathrm{LDR}}+R_{\mathrm fixed})$. Answer: D.
Q33 Medium10.3
An NTC thermistor is the upper resistor of a divider; the output is across a lower fixed resistor. What happens to the output when temperature rises?
A. It increases.
B. It decreases.
C. It becomes the thermistor resistance.
D. It must become zero.
An NTC thermistor's resistance decreases as temperature rises, so the fixed lower resistor receives a larger fraction of the supply p.d. Answer: A.
Q34 Easy10.3
A cell balances on a potentiometer wire at length $l$. The wire's potential gradient is $k$. Which equation applies at null?
A. $\varepsilon=k/l$
B. $\varepsilon=l/k$
C. $\varepsilon=kl$
D. $\varepsilon=k+l$
At balance, the test-cell e.m.f. equals the p.d. along the balance length: $\varepsilon=kl$. Answer: C.
Q35 Medium10.3
The p.d. across a uniform $1.00\,\mathrm m$ potentiometer wire is $2.50\,\mathrm V$. A cell balances at $0.640\,\mathrm m$. What is its e.m.f.?
A. $0.256\,\mathrm V$
B. $1.60\,\mathrm V$
C. $2.50\,\mathrm V$
D. $3.91\,\mathrm V$
$k=2.50/1.00=2.50\,\mathrm{V\,m^{-1}}$, so $\varepsilon=kl=(2.50)(0.640)=1.60\,\mathrm V$. Answer: B.
Q36 Medium10.3
Cell X of e.m.f. $1.20\,\mathrm V$ balances at $0.450\,\mathrm m$. Cell Y balances at $0.600\,\mathrm m$ without changing the primary current. What is the e.m.f. of Y?
A. $0.90\,\mathrm V$
B. $1.20\,\mathrm V$
C. $1.35\,\mathrm V$
D. $1.60\,\mathrm V$
With the same potential gradient, $\varepsilon_Y/\varepsilon_X=l_Y/l_X$. Thus $\varepsilon_Y=1.20(0.600/0.450)=1.60\,\mathrm V$. Answer: D.
Q37 Medium10.3
Which statement is true at the balance point of a potentiometer?
A. No current flows through the galvanometer or test cell, but current still flows in the primary circuit.
B. No current flows anywhere in the apparatus.
C. The potentiometer wire has zero p.d. across it.
D. The test cell is short-circuited.
Null applies to the test branch only. The primary circuit must keep current in the uniform wire to maintain a potential gradient. Answer: A.
Q38 Hard10.3
A $2.0\,\mathrm V$ test cell is connected correctly, but the total p.d. along the potentiometer wire is only $1.5\,\mathrm V$. No balance point is found. Which change can produce a balance?
A. Reverse only the galvanometer terminals.
B. Reduce the primary current.
C. Increase the primary current so that the total wire p.d. exceeds $2.0\,\mathrm V$.
D. Replace the galvanometer with an ammeter in series.
The wire cannot supply a matching p.d. if its entire p.d. is below the test e.m.f. Increasing the primary current increases the potential gradient and total wire p.d. Answer: C.
Q39 Hard10.3
The series control resistance in the potentiometer's primary circuit is reduced. The test cell is unchanged and a balance remains possible. What happens to its balance length?
A. It increases because current increases.
B. It decreases because the potential gradient increases.
C. It is unchanged because the test-cell e.m.f. is unchanged.
D. It becomes zero for every setting.
Reducing control resistance increases primary current and $k$. Since $l=\varepsilon/k$ for the unchanged test cell, the balance length decreases. Answer: B.
Q40 Hard10.3
Why can a potentiometer give a more accurate comparison of cell e.m.f.s than direct readings from a finite-resistance voltmeter?
A. It makes each cell's internal resistance zero.
B. It always uses a longer scale than a voltmeter.
C. It supplies current to both test cells continuously.
D. At null it draws no current from the test cell, so there are no lost volts in that cell.
A null measurement does not load the test cell. With zero test-cell current, its terminal p.d. equals its e.m.f. Answer: D.
Paper 2 · Structured
Try each scenario on paper before revealing the worked mark guide. Marks shown are an original PHYSICS CREST training allocation.
S1. Investigating a cell Hard10.112 marks
A student changes the current supplied by a cell and records its terminal p.d. Two readings are $(I,V)=(0.20\,\mathrm A,6.30\,\mathrm V)$ and $(1.20\,\mathrm A,5.30\,\mathrm V)$.
(a) Draw a circuit containing the cell, a switch, a variable resistor and an ammeter in series, with a voltmeter connected to measure the terminal p.d. of the cell. [3]
(b) Define the e.m.f. of the cell. [2]
(c) Use the readings to determine (i) the internal resistance and (ii) the e.m.f. [3]
(d) Distinguish between the e.m.f. and the terminal p.d. while the cell supplies current. [2]
(e) Explain why the switch should be opened between readings. [1]
(f) State the approximate reading of a high-resistance voltmeter connected across the unloaded cell. [1]
(a) Cell, switch, variable resistor and ammeter form one unbroken series loop [1]; voltmeter is connected directly across the cell terminals [1]; clear standard symbols and junctions [1].
(b) E.m.f. is the energy transferred by the source to electrical energy [1] per unit charge around the complete circuit [1].
(c) Gradient $=(5.30-6.30)/(1.20-0.20)=-1.00\,\mathrm{V\,A^{-1}}$, so $r=1.00\,\Omega$ [2]. $\varepsilon=V+Ir=6.30+(0.20)(1.00)=6.50\,\mathrm V$ [1].
(d) E.m.f. is the energy supplied per coulomb by the source; terminal p.d. is the energy per coulomb available to the external circuit [1]. While supplying current, $V=\varepsilon-Ir$ because $Ir$ is transferred internally [1].
(e) To limit heating/change of temperature and hence resistance during the investigation [1].
(f) Approximately $6.50\,\mathrm V$ [1].
S2. Complete circuit and charging Hard10.110 marks
A source has e.m.f. $12.0\,\mathrm V$ and internal resistance $0.50\,\Omega$. It first supplies a $4.0\,\Omega$ load.
(a) Starting from Kirchhoff's second law, derive $I=\varepsilon/(R+r)$. [2]
(b) Calculate the current. [2]
(c) Calculate the terminal p.d. using two different equations. [2]
(d) State the energy transferred inside the source per coulomb. [1]
(e) Calculate the power dissipated in the internal resistance. [1]
(f) The source is now charged by a current of $1.20\,\mathrm A$ entering its positive terminal. Calculate its terminal p.d. while charging. [2]
(a) Around the supplying loop, $\varepsilon=IR+Ir$ [1], hence $I=\varepsilon/(R+r)$ [1].
(f) During charging, $V=\varepsilon+Ir$ [1] $=12.0+(1.20)(0.50)=12.6\,\mathrm V$ [1].
S3. Deriving resistor combinations Hard10.212 marks
The network consists of a $4.0\,\Omega$ resistor in series with a parallel pair of $6.0\,\Omega$ and $3.0\,\Omega$. It is connected to an ideal $18.0\,\mathrm V$ supply.
(a) Derive the expression $R_{\mathrm s}=R_1+R_2+\cdots$ for resistors in series. [3]
(b) Derive the expression $1/R_{\mathrm p}=1/R_1+1/R_2+\cdots$ for resistors in parallel. [4]
(c) For the stated network, calculate (i) the total resistance, (ii) the supply current, and (iii) the current in each parallel branch. [5]
(a) Series components carry the same current $I$ [1]. $V=V_1+V_2+\cdots=IR_1+IR_2+\cdots$ [1]. Since $V=IR_{\mathrm s}$, $R_{\mathrm s}=R_1+R_2+\cdots$ [1].
(b) Parallel branches have the same p.d. $V$ [1]. By the junction law, $I=I_1+I_2+\cdots$ [1]. Thus $V/R_{\mathrm p}=V/R_1+V/R_2+\cdots$ [1], and division by $V$ gives $1/R_{\mathrm p}=1/R_1+1/R_2+\cdots$ [1].
(c) $6.0\,\Omega\parallel3.0\,\Omega=2.0\,\Omega$, so $R_{\mathrm total}=4.0+2.0=6.0\,\Omega$ [2]. Supply current $=18.0/6.0=3.0\,\mathrm A$ [1]. The parallel pair has p.d. $(3.0)(2.0)=6.0\,\mathrm V$, so $I_{6\Omega}=1.0\,\mathrm A$ and $I_{3\Omega}=2.0\,\mathrm A$ [2].
S4. Switching a parallel branch Hard10.210 marks
An ideal $12.0\,\mathrm V$ source supplies a $3.0\,\Omega$ resistor $R_1$ in series with a branch containing $R_2=6.0\,\Omega$. Closing switch S connects a second $6.0\,\Omega$ resistor $R_3$ in parallel with $R_2$.
(a) With S open, calculate (i) the total resistance, (ii) the source current and (iii) the p.d. across $R_2$. [3]
(b) With S closed, calculate (i) the total resistance, (ii) the source current and (iii) the current in each parallel branch. [4]
(c) Calculate the factor by which the power in $R_1$ changes when S is closed. [2]
(d) Explain why the p.d. across $R_2$ decreases when S is closed. [1]
(b) $R_2\parallel R_3=3.0\,\Omega$ and $R_{\mathrm total}=3.0+3.0=6.0\,\Omega$ [2]. Source current $=12.0/6.0=2.0\,\mathrm A$ [1]. Equal branches split this equally, so each carries $1.0\,\mathrm A$ [1].
(c) $P_{R1}\propto I^2$, so factor $=(2.0/1.33)^2=2.25$ [2].
(d) The larger source current produces a larger p.d. across series resistor $R_1$, leaving a smaller part of the fixed supply p.d. across the parallel section [1].
S5. Three-branch Kirchhoff network Hard10.1/10.212 marks
Three branches connect nodes A and B. The current arrows shown are chosen directions. The $1.0\,\Omega$ resistance is the internal resistance of the $10.0\,\mathrm V$ source.
(a) State the conservation principle associated with each Kirchhoff law. [2]
(b) Write the junction equation at A. [1]
(c) Write two independent loop equations. [4]
(d) Solve for $I_1$, $I_2$ and $I_3$. [3]
(e) Calculate the terminal p.d. of the $10.0\,\mathrm V$ source and verify it using the centre branch. [2]
(a) First law: conservation of charge [1]. Second law: conservation of energy [1].
(d) Solving the three equations gives $I_2=2.0\,\mathrm A$, $I_3=2.0\,\mathrm A$ and $I_1=4.0\,\mathrm A$ [3].
(e) $V=\varepsilon-I_1r=10.0-(4.0)(1.0)=6.0\,\mathrm V$ [1]. The centre branch gives $V=I_2R=(2.0)(3.0)=6.0\,\mathrm V$ [1].
S6. Opposing source branches Hard10.1/10.212 marks
Three branches connect nodes P and Q. The positive terminal of each source is connected towards P. Currents $I_1$, $I_2$ and $I_3$ are initially assumed to flow from P to Q. Let $V=V_P-V_Q$.
(a) Write $I_1$, $I_2$ and $I_3$ in terms of $V$. [3]
(b) Apply Kirchhoff's first law and calculate $V$. [3]
(c) Calculate the three branch currents. [3]
(d) Interpret the sign of $I_3$. [1]
(e) Identify which source is being charged and explain your choice. [2]
(a) For each assumed P-to-Q direction, $V=\varepsilon+IR$. Hence $I_1=(V-8.0)/2.0$ [1], $I_2=V/5.0$ [1] and $I_3=(V-12.0)/1.0$ [1].
(b) With all three arrows defined from P to Q, $I_1+I_2+I_3=0$ [1]. Thus $(V-8)/2+V/5+(V-12)=0$ [1], giving $V=160/17=9.41\,\mathrm V$ [1].
(d) The $12.0\,\mathrm V$ branch current is actually $2.59\,\mathrm A$ from Q to P, opposite to the assumed arrow [1].
(e) The $8.0\,\mathrm V$ source is being charged [1], because $I_1$ enters its positive terminal at P [1].
S7. Loaded potential divider Hard10.2/10.310 marks
A divider has an upper resistor $R_1=3.0\,\mathrm{k}\Omega$ and a lower resistor $R_2=6.0\,\mathrm{k}\Omega$ across an ideal $12.0\,\mathrm V$ supply. The output is across $R_2$.
(a) Derive $V_{\mathrm{out}}=V_{\mathrm{in}}R_2/(R_1+R_2)$ for the unloaded divider. [2]
(b) Calculate the unloaded output. [1]
(c) A $6.0\,\mathrm{k}\Omega$ load is connected across $R_2$. Calculate (i) the equivalent lower resistance and (ii) the loaded output. [3]
(d) Calculate the current in the load. [1]
(e) Explain why a high-resistance voltmeter causes less loading. [2]
(f) State the resistance of an ideal voltmeter. [1]
(a) Divider current $I=V_{\mathrm{in}}/(R_1+R_2)$ [1]. Since $V_{\mathrm{out}}=IR_2$, $V_{\mathrm{out}}=V_{\mathrm{in}}R_2/(R_1+R_2)$ [1].
(c) $6.0\,\mathrm{k}\Omega\parallel6.0\,\mathrm{k}\Omega=3.0\,\mathrm{k}\Omega$ [1]. The loaded divider is therefore $3.0\,\mathrm{k}\Omega$ over $3.0+3.0\,\mathrm{k}\Omega$, giving $V_{\mathrm{out}}=6.0\,\mathrm V$ [2].
(e) A larger meter resistance takes less current [1] and changes the effective parallel/output resistance by a smaller amount [1].
(f) Infinite resistance [1].
S8. LDR and thermistor divider reasoning Hard10.310 marks
Two dividers use a $10\,\mathrm{k}\Omega$ fixed resistor and the same LDR across $9.0\,\mathrm V$. The LDR resistance is $40\,\mathrm{k}\Omega$ in darkness and $5.0\,\mathrm{k}\Omega$ in bright light. In circuit A the output is across the lower LDR. In circuit B the LDR is upper and the output is across the lower fixed resistor.
(a) State how LDR resistance changes as light intensity increases. [1]
(b) Calculate the output of circuit A in darkness and in bright light. [3]
(c) Calculate the output of circuit B in darkness and in bright light. [3]
(d) Select the circuit that gives a high output in bright light. [1]
(e) The upper LDR in circuit B is replaced by an NTC thermistor. Explain how the output changes as temperature rises. [2]
(a) LDR resistance decreases as light intensity increases [1].
(b) Use the lower-resistor fraction [1]. Darkness: $V_A=9.0[40/(10+40)]=7.2\,\mathrm V$ [1]. Bright: $V_A=9.0[5.0/(10+5.0)]=3.0\,\mathrm V$ [1].
(c) Use the fixed-lower fraction [1]. Darkness: $V_B=9.0[10/(40+10)]=1.8\,\mathrm V$ [1]. Bright: $V_B=9.0[10/(5.0+10)]=6.0\,\mathrm V$ [1].
(d) Circuit B [1].
(e) NTC thermistor resistance decreases as temperature rises [1], so the lower fixed resistor receives a larger fraction and the output rises [1].
S9. Comparing e.m.f.s by potentiometer Hard10.312 marks
A uniform potentiometer wire AB is $1.20\,\mathrm m$ long and has p.d. $3.00\,\mathrm V$ across it. A standard cell of e.m.f. $1.50\,\mathrm V$ balances at $0.600\,\mathrm m$. An unknown cell balances at $0.472\,\mathrm m$ without changing the primary current.
(a) Distinguish between the primary circuit and the test circuit. [2]
(b) Define potential gradient and calculate it for wire AB. [2]
(c) Calculate the unknown e.m.f. directly from the gradient. [2]
(d) Verify the result using the ratio of balance lengths. [2]
(e) Explain what null means and why it avoids loading the test cell. [2]
(f) The series control resistance is increased. Predict and explain the change in the unknown cell's balance length. [2]
(a) The primary circuit drives a steady current through wire AB [1]; the separate test circuit contains the test cell, galvanometer and sliding contact [1].
(b) Potential gradient is p.d. per unit length [1]. $k=3.00/1.20=2.50\,\mathrm{V\,m^{-1}}$ [1].
(d) $\varepsilon_{\mathrm u}/1.50=0.472/0.600$ [1], so $\varepsilon_{\mathrm u}=1.18\,\mathrm V$ [1].
(e) At null the galvanometer reads zero and no current flows through the test cell [1]. Therefore there are no lost volts in that cell, so its e.m.f. is compared directly with the wire p.d. [1].
(f) Increasing control resistance lowers primary current and potential gradient [1]; since $l=\varepsilon/k$, the unchanged test e.m.f. balances at a greater length [1].
S10. Source, sensor and loaded output Hard10.1–10.312 marks
A source of e.m.f. $9.0\,\mathrm V$ and internal resistance $1.0\,\Omega$ supplies a series divider made from an upper NTC thermistor and a lower $2.0\,\Omega$ fixed resistor. The output is across the fixed resistor. The thermistor resistance is $4.0\,\Omega$ at a lower temperature and $1.0\,\Omega$ at a higher temperature.
(a) Explain why it is incorrect to use $9.0\,\mathrm V$ as the divider's terminal input without considering the internal resistance. [2]
(b) At the lower temperature, calculate (i) the source current, (ii) the source terminal p.d. and (iii) the output p.d. [4]
(c) At the higher temperature, calculate the output p.d. before any load is connected. [2]
(d) Explain physically why the output rises as temperature rises. [1]
(e) At the higher temperature, a $2.0\,\Omega$ load is connected across the fixed resistor. Calculate (i) the equivalent lower resistance, (ii) the loaded output and (iii) the load current. [3]
(a) When current flows, the internal resistance has p.d. $Ir$ across it [1], so the divider input is the terminal p.d. $V=\varepsilon-Ir$, not automatically the e.m.f. [1].
(b) Total resistance $=1.0+4.0+2.0=7.0\,\Omega$, so $I=9.0/7.0=1.29\,\mathrm A$ [2]. Terminal p.d. $=9.0-(1.29)(1.0)=7.71\,\mathrm V$ [1]. Output $=I(2.0)=2.57\,\mathrm V$ [1].
(c) Total resistance $=1.0+1.0+2.0=4.0\,\Omega$, so $I=2.25\,\mathrm A$ and $V_{\mathrm{out}}=(2.25)(2.0)=4.50\,\mathrm V$ [2].
(d) The NTC resistance decreases, so the fixed lower resistor becomes a larger fraction of the external resistance/terminal p.d. [1].
(e) $2.0\,\Omega\parallel2.0\,\Omega=1.0\,\Omega$ [1]. Total including $r$ is $1.0+1.0+1.0=3.0\,\Omega$, so total current is $3.0\,\mathrm A$ and loaded output is $(3.0)(1.0)=3.0\,\mathrm V$ [1]. Load current $=3.0/2.0=1.5\,\mathrm A$ [1].