Skip to lesson
1

Topic 10 · D.C. Circuits

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

The whole topic in one picture
A source gives charge energy per coulomb. Current carries that charge through a network. Kirchhoff's first law tracks charge at junctions; Kirchhoff's second law tracks energy around loops. Potential dividers then use those ideas to produce a chosen or sensor-dependent p.d.
Exact Topic 10 boundary
10.1: circuit symbols and diagrams, e.m.f., e.m.f.–p.d. distinction, internal resistance and terminal p.d.
10.2: both Kirchhoff laws, derivation and use of series/parallel resistance, and simple circuit analysis.
10.3: potential dividers, potentiometer comparison, galvanometer null methods, and LDR/thermistor divider circuits.

10.1 · Practical circuits

  • A circuit must satisfy charge conservation at junctions and energy conservation around complete loops.
  • A source’s e.m.f. is not automatically its terminal potential difference when internal resistance carries current.
Read a circuit as a map
  • A continuous wire is one node: every point on that ideal wire is at the same potential.
  • A filled dot marks a junction. Crossing lines without a junction dot are not automatically connected.
  • An ammeter is placed in series and is treated as having negligible resistance.
  • A voltmeter is connected across two points and is treated as having very large resistance.
  • Trace the actual conducting paths before deciding which components are in series or parallel.
A load R V cell I
Correct meter positions: series ammeter, parallel voltmeter.
Fast topology test
  1. Cover the labels.
  2. Mark the nodes.
  3. Ask whether current can split.
  4. Only then use series/parallel rules.

A diagram can look like a rectangle and still contain parallel branches. Shape is not topology.

Common mistake
“Next to each other” does not mean series. Two components are in series only when the same current must pass through both with no junction between them. They are in parallel only when both ends connect to the same two nodes.
Quick Check 1
A voltmeter is accidentally connected in series with a lamp. Explain why the lamp is almost off.
A voltmeter has a very large resistance. In series it makes the circuit resistance very large, so the current is almost zero.
2

Circuit-symbol sheet

The syllabus can use any symbol below in an examination diagram. Learn the shape, name and connection points. Recognition of a capacitor or a.c. supply symbol here does not add their later-topic physics to Topic 10.

Cell
Switch
Battery of cells
Earth
Power supply
Electric bell
A.c. power supply
Buzzer
Junction
Microphone
Lamp
Loudspeaker
Fixed resistor
MotorM
Variable resistor
GeneratorG
Thermistor
AmmeterA
Light-dependent resistor
VoltmeterV
Heater
Galvanometer
Potentiometer
Oscilloscope
Diode
Capacitor
Light-emitting diode
Drawing standard
Use straight wires, leave clear gaps at switches, draw long/short cell plates distinctly, place junction dots deliberately, label component values beside—not through—the symbol, and make meter connections unambiguous.
3

E.m.f., p.d. and internal resistance

One coulomb's energy journey

E.m.f. $\varepsilon$ is the energy transferred by a source from other forms to electrical energy per unit charge as it drives charge around a complete circuit:

$$\boxed{\varepsilon=\frac{W_{\text{source}}}{Q}}$$

Potential difference $V$ across a component is the electrical energy transferred to other forms per unit charge in that component:

$$\boxed{V=\frac{W_{\text{component}}}{Q}}$$

Both have unit $\mathrm{J\,C^{-1}}=\mathrm V$, but they describe opposite sides of the energy account: the source supplies energy; components transfer it.

QuantityEnergy statementWhere measured
E.m.f. $\varepsilon$Energy supplied per coulomb by the sourceAcross an unloaded source, a high-resistance voltmeter reads approximately $\varepsilon$
Terminal p.d. $V$Energy per coulomb available to the external circuitAcross the source terminals while it supplies current
Lost volts $Ir$Energy per coulomb transferred inside the sourceAcross the source's internal resistance
A external load R V internal r ε current I terminal p.d. V = IR
The internal resistance is a model inside the source; the voltmeter is across the external load.

Deriving the complete-circuit equation

Kirchhoff's second law says energy gained per coulomb equals energy transferred per coulomb around the loop:

$$\varepsilon=IR+Ir=I(R+r)$$

The terminal p.d. is the external part:

$$\boxed{V=IR=\varepsilon-Ir}\qquad\boxed{\text{lost volts}=Ir=\varepsilon-V}$$
Open circuit
$I\approx0$, so $Ir\approx0$ and $V\approx\varepsilon$.
Supplying current
$I>0$, so $V=\varepsilon-Ir<\varepsilon$.
Being charged
Current enters the positive terminal, so terminal p.d. is $V=\varepsilon+Ir$.
Very small external $R$
Current can be large; do not treat $I=\varepsilon/r$ as a safe experimental instruction.
E.m.f. is not a force
E.m.f. is an energy-per-charge quantity. Also, do not say energy is “used up before charge leaves the cell”. Energy is transferred in the internal processes represented by $r$ while current flows.

The high-value graph

εI / AV / Vgradient = −r
From $V=\varepsilon-rI$:
  • vertical intercept $=\varepsilon$
  • gradient $=\Delta V/\Delta I=-r$
  • use widely separated points on the best-fit line
  • include the negative sign in the gradient, then report $r$ as a positive resistance
Worked example
A source has $\varepsilon=8.4\,\mathrm V$ and $r=0.60\,\Omega$, connected to $R=3.6\,\Omega$.
$I=\varepsilon/(R+r)=8.4/4.2=2.0\,\mathrm A$.
$V=IR=(2.0)(3.6)=7.2\,\mathrm V$.
Lost volts $=Ir=(2.0)(0.60)=1.2\,\mathrm V$. Check: $7.2+1.2=8.4\,\mathrm V$.
Quick Check 2
A cell gives terminal readings $(I,V)=(0.40\,\mathrm A,5.4\,\mathrm V)$ and $(1.20\,\mathrm A,4.6\,\mathrm V)$. Find $r$ and $\varepsilon$.
Gradient $=(4.6-5.4)/(1.20-0.40)=-1.0\,\Omega$, so $r=1.0\,\Omega$. Using $V=\varepsilon-Ir$: $\varepsilon=5.4+(0.40)(1.0)=5.8\,\mathrm V$.
A cell delivers more current through a fixed internal resistance. What happens to its lost volts Ir?

Your turn · Find current for e.m.f. 12 V, external resistance 5 Ω and internal resistance 1 Ω.

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

4

10.2 · Kirchhoff's laws

  • Choose current directions and follow a consistent sign convention around loops.
  • A negative solved current means its actual direction is opposite to your assumption.
  • For a cell delivering current, terminal p.d. equals e.m.f. minus Ir.
First law — junction rule
At any junction, the algebraic sum of currents is zero. Equivalently, $$\boxed{\sum I_{\text{in}}=\sum I_{\text{out}}}$$ This follows from conservation of charge: charge does not build up at a steady-current junction.
I₁I₂I₃I₄I₅
For the arrows shown: $$I_1+I_2=I_3+I_4+I_5$$ If a calculated current is negative, the magnitude is valid but its real direction is opposite to the arrow you chose.
Second law — loop rule
Around any closed loop, the algebraic sum of e.m.f.s and p.d.s is zero. Equivalently, $$\boxed{\sum \varepsilon=\sum IR}$$ This follows from conservation of energy: each coulomb returns to its starting point with no net energy change.
While tracing a loopTerm
Cross a source from short plate $(-)$ to long plate $(+)$$+\varepsilon$
Cross a source from long plate $(+)$ to short plate $(-)$$-\varepsilon$
Move through a resistor in the chosen current direction$-IR$
Move through a resistor opposite to the chosen current direction$+IR$
Never memorise one clockwise formula
Choose a loop direction and apply the signs consistently. Reversing the loop reverses every term and gives the same physics.

Required derivation: resistors in series

The same current $I$ flows through $R_1,R_2,\ldots$. By Kirchhoff's second law:

$$V=V_1+V_2+\cdots=IR_1+IR_2+\cdots$$ For the equivalent resistor, $V=IR_{\mathrm s}$. Therefore $$IR_{\mathrm s}=I(R_1+R_2+\cdots)\quad\Rightarrow\quad\boxed{R_{\mathrm s}=R_1+R_2+\cdots}$$

Required derivation: resistors in parallel

Every branch has the same p.d. $V$. By Kirchhoff's first law:

$$I=I_1+I_2+\cdots=\frac{V}{R_1}+\frac{V}{R_2}+\cdots$$ For the equivalent resistor, $I=V/R_{\mathrm p}$. Therefore $$\frac{V}{R_{\mathrm p}}=V\left(\frac1{R_1}+\frac1{R_2}+\cdots\right)\quad\Rightarrow\quad\boxed{\frac1{R_{\mathrm p}}=\frac1{R_1}+\frac1{R_2}+\cdots}$$
Instant checks
Series resistance must exceed every individual resistance. Parallel resistance must be smaller than the smallest branch resistance. For two resistors, $R_{\mathrm p}=R_1R_2/(R_1+R_2)$.
Quick Check 3
A $12\,\Omega$ resistor and an unknown resistor are in parallel. Their combined resistance is $3.0\,\Omega$. Find the unknown resistance.
$1/3.0=1/12+1/R$, so $1/R=1/3-1/12=1/4$ and $R=4.0\,\Omega$. The answer is smaller than neither branch; the combined $3.0\,\Omega$ is smaller than both.
5

Solving a multi-loop circuit

  1. Mark the nodes and choose a current arrow for every branch.
  2. Write one independent junction equation.
  3. Choose independent loops and write signed energy equations.
  4. Solve the simultaneous equations with units.
  5. Check each junction and loop; interpret any negative current.
AB R₁ = 2 Ω ε₁ = 12 V+− R₃ = 4 Ω R₂ = 2 Ω ε₂ = 2 V+− I₁ I₂ I₃
Chosen arrows: $I_1$ enters node A; $I_2$ and $I_3$ leave it.
Worked solution
At node A: $$I_1=I_2+I_3\tag{1}$$ Left loop, travelling from B up the left branch and down the centre: $$12=2I_1+4I_2\tag{2}$$ Right loop, travelling down the centre and up the right branch: $$4I_2=2+2I_3\tag{3}$$ From (3), $I_3=2I_2-1$. From (1), $I_1=3I_2-1$. Substituting in (2): $$12=2(3I_2-1)+4I_2\Rightarrow I_2=1.4\,\mathrm A$$ Hence $I_3=1.8\,\mathrm A$ and $I_1=3.2\,\mathrm A$.

Checks: $3.2=1.4+1.8$ at A; left loop gives $2(3.2)+4(1.4)=12\,\mathrm V$; right relation gives $4(1.4)=2+2(1.8)=5.6\,\mathrm V$.

Three traps
  • Do not use a resistor's current in the wrong $IR$ term.
  • Do not count two loop equations that are algebraic copies of each other.
  • Do not erase a negative answer: reverse the stated direction and keep the positive magnitude.

Switches and hidden short circuits

An open switch removes its branch. A closed switch with negligible resistance can join two nodes and bypass a component. Redraw the conducting circuit after each switch change before calculating.

Quick Check 4
A calculation gives $I_3=-0.24\,\mathrm A$ for an arrow drawn from P to Q. State the physical result.
The current has magnitude $0.24\,\mathrm A$ and flows from Q to P, opposite to the chosen arrow.
6

10.3 · Potential dividers

The principle
Two resistors in series carry the same current. The supply p.d. divides in the same ratio as their resistances. For the output across $R_2$: $$I=\frac{V_{\mathrm{in}}}{R_1+R_2}$$ $$\boxed{V_{\mathrm{out}}=IR_2=V_{\mathrm{in}}\frac{R_2}{R_1+R_2}}$$ Always identify the two output nodes; the numerator is the resistance directly between those nodes in the unloaded divider.
Vin+− R1 M R2 VVout
$V_{\mathrm{out}}$ is measured from midpoint M to the lower node, so it is across $R_2$.
Numerator trap
Do not call a resistor “top” or “bottom” without checking the output terminals. Use the resistance across which the output is measured.

Loaded divider

If a device of resistance $R_L$ is connected across $R_2$, the lower section becomes $R_2\parallel R_L$. Calculate that equivalent resistance first:

$$V_{\mathrm{out}}=V_{\mathrm{in}}\frac{R_2\parallel R_L}{R_1+(R_2\parallel R_L)}$$

A finite load usually reduces the output compared with an ideal high-resistance voltmeter. This is ordinary series/parallel analysis, not a separate formula to memorise.

Sensor dividers: use a two-step argument

  1. State how the sensor resistance changes: more light lowers an LDR's resistance; higher temperature lowers an NTC thermistor's resistance.
  2. Identify whether the output is across the sensor or the fixed resistor, then use the fraction.
Sensor positionSensor resistance decreasesSensor resistance increases
Output measured across the sensor$V_{\mathrm{out}}$ decreases$V_{\mathrm{out}}$ increases
Output measured across the fixed resistor$V_{\mathrm{out}}$ increases$V_{\mathrm{out}}$ decreases
output across LDRoutput across fixed resistor fixedLDRV LDRfixedV
Bright light lowers LDR resistance: left output falls; right output rises.
Design language
For an output p.d. that rises in darkness, measure across the LDR: darkness increases its resistance and therefore its share of the supply p.d. Output across the fixed resistor falls in darkness. Whether a device activates depends on its switching threshold and circuit arrangement. State the actual two output nodes.
Quick Check 5
A $9.0\,\mathrm V$ divider contains a $6.0\,\mathrm{k}\Omega$ fixed resistor in series with an NTC thermistor. The output is across the fixed resistor. Find the output when the thermistor is (a) $12\,\mathrm{k}\Omega$ and (b) $3.0\,\mathrm{k}\Omega$.
(a) $V_{out}=9.0(6.0)/(12+6.0)=3.0\,\mathrm V$. (b) $V_{out}=9.0(6.0)/(3.0+6.0)=6.0\,\mathrm V$. Heating an NTC thermistor lowers its resistance, so the fixed-resistor output rises.
7

Potentiometer and the null method

Two connected circuits, two different currents
The primary circuit drives a steady current through uniform wire AB, giving a constant potential gradient $k$. The test circuit contains the cell being measured, galvanometer and sliding contact J. At balance, the galvanometer reads zero.
control R driver+ ABuniform resistance wire J galvanometer test cell Ex+ balance length l
The test cell's positive terminal is connected to the high-potential end A.

Balance equations

For uniform wire AB of length $L$ with p.d. $V_{AB}$:

$$\boxed{k=\frac{V_{AB}}{L}}\qquad(\text{unit }\mathrm{V\,m^{-1}})$$

At null, the test-cell e.m.f. equals the p.d. along balance length $l$:

$$\boxed{\varepsilon_x=kl}$$

If two p.d.s are compared without changing the primary current:

$$\boxed{\frac{V_1}{V_2}=\frac{l_1}{l_2}}$$
What “null” really means
At balance, no current flows through the galvanometer or test cell, so there is no lost volts in the test cell. Current still flows in the primary circuit and potentiometer wire.
Worked example
The p.d. along a $1.20\,\mathrm m$ wire is $2.40\,\mathrm V$. A cell balances at $0.735\,\mathrm m$.
$k=2.40/1.20=2.00\,\mathrm{V\,m^{-1}}$.
$\varepsilon=kl=(2.00)(0.735)=1.47\,\mathrm V$.
For a usable balanceWhy
Uniform wire and steady primary currentPotential gradient must remain constant.
Correct polarityThe test e.m.f. must oppose the wire p.d.
Test p.d. smaller than total wire p.d.Otherwise no balance point lies on AB.
Use a galvanometerIts sensitivity reveals the zero-current condition and direction of imbalance.
Quick Check 6
Cells X and Y balance at $0.480\,\mathrm m$ and $0.640\,\mathrm m$. If $\varepsilon_X=1.20\,\mathrm V$, find $\varepsilon_Y$.
$\varepsilon_Y/\varepsilon_X=l_Y/l_X=0.640/0.480=4/3$. Hence $\varepsilon_Y=(1.20)(4/3)=1.60\,\mathrm V$.
8

Exam toolbox

Definition response
Name the energy transfer, state “per unit charge”, and distinguish source from component.
Network response
Mark nodes, label branch currents, write equations before substituting numbers.
Sensor response
Resistance change → measured fraction → output change. Never jump directly to “voltage rises”.
Null-method response
State zero galvanometer current, matching p.d.s, and no current through the test cell.
Common mistakes checklist
  • Using $\varepsilon=V$ while a source supplies current.
  • Calling Kirchhoff's first law conservation of current instead of charge.
  • Adding parallel resistances directly.
  • Ignoring cell polarity or an assumed current direction.
  • Using the wrong resistor in the divider numerator.
  • Assuming a voltmeter draws the branch current.
  • Saying null means there is no current anywhere.
  • Using a potentiometer as though it were only a two-terminal variable resistor.

Master Equation Sheet

IdeaEquationMeaning/check
E.m.f.$\varepsilon=W_{\mathrm{source}}/Q$Energy supplied per coulomb
Potential difference$V=W_{\mathrm{component}}/Q$Energy transferred per coulomb
Complete circuit$\varepsilon=I(R+r)$One source, external $R$, internal $r$
Terminal p.d.$V=\varepsilon-Ir=IR$Source supplying current
Charging source$V=\varepsilon+Ir$Current enters positive terminal
First law$\sum I_{in}=\sum I_{out}$Conservation of charge
Second law$\sum \varepsilon=\sum IR$Conservation of energy
Series$R_s=R_1+R_2+\cdots$$R_s$ exceeds every component
Parallel$1/R_p=1/R_1+1/R_2+\cdots$$R_p$ below smallest branch
Divider$V_{out}=V_{in}\,R_2/(R_1+R_2)$$R_2$ lies across output nodes
Potential gradient$k=V_{AB}/L$Uniform wire, steady current
Potentiometer$V=kl$, $V_1/V_2=l_1/l_2$Valid at balance
Final exam habit
After every calculation, ask three questions: Does the unit fit? Does the direction/sign make physical sense? Does the value pass a limiting check? A parallel resistance larger than a branch or a divider output larger than its supply signals an error immediately.
Final Quick Check
A source with $\varepsilon=9.0\,\mathrm V$ and $r=1.0\,\Omega$ supplies a divider made from $R_1=2.0\,\Omega$ and $R_2=3.0\,\Omega$. Find the current, terminal p.d. and p.d. across $R_2$.
Total resistance $=1.0+2.0+3.0=6.0\,\Omega$, so $I=9.0/6.0=1.5\,\mathrm A$. Terminal p.d. $=9.0-(1.5)(1.0)=7.5\,\mathrm V$. Across $R_2$: $V_2=(1.5)(3.0)=4.5\,\mathrm V$.