Skip to lesson
PCPHYSICS CREST
AP Physics 1 · Unit 2 Practice MCQs (1-30) FRQs (1-8) NotesExam Arena
P

Unit 2 Practice — Force & Dynamics

How to use this section
MCQs (1–30): Work through all nine Unit 2 topics. Each item trains a specific AP reasoning pattern; each includes a physics diagram. Click an option only after committing to an answer.
FRQs (1–8): Two original training questions for each current AP free-response routine: Mathematical Routines (10 pts), Translation Between Representations (12 pts), Experimental Design and Analysis (10 pts), and Qualitative/Quantitative Translation (8 pts). Try each on paper before revealing the rubric.
Difficulty tags: Easy · Medium · Hard · A*.
Coverage map
2.1 Systems & center of mass · 2.2 Forces & FBDs · 2.3 Newton III & tension · 2.4 Equilibrium · 2.5 Newton II · 2.6 Gravity & apparent weight · 2.7 Friction · 2.8 Springs · 2.9 Circular motion, banking & circular orbits.

Multiple Choice Questions

Q1. Medium 2.1
Three crates are placed on a warehouse floor. Crate P (4 kg) is at position $(2, 8)$ m, Crate Q (2 kg) is at $(6, 4)$ m, and Crate R (6 kg) is at $(10, 2)$ m. What is the center of mass of the three-crate system?
x / my / m024681012246810P: 4 kgQ: 2 kgR: 6 kg
  • A. $(6.0, 4.7)$ m
  • B. $(6.67, 4.33)$ m
  • C. $(7.5, 3.5)$ m
  • D. $(8.0, 5.0)$ m
$x_{cm} = \dfrac{(4)(2)+(2)(6)+(6)(10)}{4+2+6} = \dfrac{8+12+60}{12} = \dfrac{80}{12} = 6.67$ m. $y_{cm} = \dfrac{(4)(8)+(2)(4)+(6)(2)}{12} = \dfrac{32+8+12}{12} = \dfrac{52}{12} = 4.33$ m. Therefore $\boxed{(x_{cm},y_{cm})=(6.67,4.33)\ \mathrm{m}}$. Answer B. (The COM is pulled toward the heaviest crate, R.)
Q2. Hard 2.2
A chest is pulled across a rough floor by a rope at an angle above the horizontal. The chest moves at constant speed. As the chest moves, the floor becomes rougher (coefficient of kinetic friction increases), but the speed and rope angle stay constant. How must the free-body diagram change?
Motionconstant speedFloor roughnessμₖ increases; rope angle fixedchoose how the real-force arrows must change
  • A. The friction arrow gets longer; the normal force arrow stays the same.
  • B. The friction arrow gets longer; the tension arrow stays the same.
  • C. The friction arrow gets longer; the tension arrow gets longer; the normal force arrow gets shorter.
  • D. The friction arrow gets longer; the tension arrow gets longer; the normal force arrow gets longer.
At fixed rope angle $\theta$, constant-speed balance gives $T\cos\theta=f_k$ and $N+T\sin\theta=mg$. Thus $T=\mu_kmg/(\cos\theta+\mu_k\sin\theta)$ and $N=mg\cos\theta/(\cos\theta+\mu_k\sin\theta)$. Increasing $\mu_k$ raises $T$ and $f_k$ while reducing $N$. To increase horizontal tension without changing the angle, the total tension must increase. But increased tension also means increased upward component ($T\sin\theta$), which reduces the normal force ($F_N = mg - T\sin\theta$). So: friction up, tension up, normal down. Answer C.
Q3. Medium 2.3
A 70 kg student stands on a bathroom scale in an elevator. The elevator starts from rest and accelerates downward at 3 m/s². Four forces are considered: $F_{student \to scale}$, $F_{scale \to student}$, $F_{Earth \to student}$ (gravity), $F_{student \to Earth}$. Which correctly ranks their magnitudes? (Use $g = 10$ m/s².)
a = 3 m/s² downscale reads support force
  • A. $(F_{s \to sc} = F_{sc \to s}) < (F_{E \to s} = F_{s \to E})$
  • B. $(F_{s \to sc} = F_{sc \to s}) > (F_{E \to s} = F_{s \to E})$
  • C. $F_{E \to s} > F_{s \to sc} > F_{sc \to s} > F_{s \to E}$
  • D. All four forces are equal.
3rd law pairs: ($F_{s \to sc}$ and $F_{sc \to s}$) are equal; ($F_{E \to s}$ and $F_{s \to E}$) are equal. The student accelerates down, so $mg - F_{scale} = ma$ → $F_{scale} = m(g-a) = 70(10-3) = 490$ N. Weight $mg = 700$ N. So scale force (490 N) < gravity (700 N). Answer A. (When elevator accelerates down, scale reads less than weight.)
Q4. Medium 2.7
A 3 kg brick is held at rest against a vertical wall by a horizontal applied force of 60 N. The coefficient of static friction between the brick and wall is $\mu_s = 0.5$. Use $g=10\,\mathrm{m/s^2}$. What is the magnitude of the friction force on the brick?
Brickmass 3 kg; at restHorizontal push60 N into wallμₛ = 0.50; g = 10 m/s²
  • A. 15 N
  • B. 30 N
  • C. 60 N
  • D. 90 N
The brick is at rest, so static friction = whatever is needed to balance gravity (up to a max). Gravity pulls down with $mg = 3 \times 10 = 30$ N. Friction pushes up with exactly 30 N to balance it. (The max possible friction is $\mu_s F_N = 0.5 \times 60 = 30$ N — so the brick is at the threshold of slipping, but actual friction equals the limiting value in this particular case.) Answer B. (Note: if $F_A$ were larger, friction would still be 30 N — it just needs to balance gravity.)
Q5. Medium 2.6
Planet Xerion has 4 times the mass of Earth and 2 times the radius of Earth. If a robot weighs 600 N on Earth, what would it weigh on the surface of Xerion?
Earthmass M; radius R; weight 600 NXerionmass 4M; radius 2Rsame robot on both spherical planets
  • A. 150 N
  • B. 300 N
  • C. 600 N
  • D. 1200 N
$g_{Xerion} = \dfrac{G \cdot 4M}{(2R)^2} = \dfrac{4GM}{4R^2} = \dfrac{GM}{R^2} = g_{Earth}$. So $g$ is the same on Xerion! Weight = 600 N. Answer C. (4× mass increases $g$ by 4×, but 2× radius decreases it by 4× — they cancel.)
Q6. Medium 2.5
Block A (3 kg) and Block B (5 kg) sit on a frictionless surface. A 24 N force pushes Block A to the right, and Block A pushes Block B. What is the contact force that Block A exerts on Block B?
A: 3 kgB: 5 kg24 N pushes A right; negligible friction24 N
  • A. 9 N
  • B. 15 N
  • C. 20 N
  • D. 24 N
System: $a = F/(m_A + m_B) = 24/8 = 3$ m/s². Isolate Block B: the only horizontal force on B is the contact force from A. $F_{contact} = m_B \cdot a = 5 \times 3 = $ 15 N. Answer B. (Check: on A, $F - F_{contact} = m_A a$ → $24 - 15 = 9 = 3 \times 3$ ✓.)
Q7. Hard 2.8
A 2 kg block is attached to a spring on a frictionless incline at 37°. Starting with the spring unstretched, the block is slowly lowered until it is at rest in equilibrium 0.3 m down the incline. What is the spring constant $k$? (Use $g = 10$ m/s², $\sin 37° \approx 0.6$.)
2 kg; extension 0.30 m37°springschematic scene; angle and labels specify the data
  • A. 40 N/m
  • B. 50 N/m
  • C. 67 N/m
  • D. 100 N/m
At equilibrium along the incline: spring force (up) = gravity component (down). $kx_0 = mg\sin\theta$ → $k = \dfrac{mg\sin\theta}{x_0} = \dfrac{2 \times 10 \times 0.6}{0.3} = \dfrac{12}{0.3} = $ 40 N/m. Answer A. (Note: it's $\sin\theta$ — the component of gravity along the incline — NOT $mg$ or $mg\cos\theta$.)
Q8. Hard 2.9
A 0.5 kg ball is attached to a 1.5 m string and moves as a conical pendulum. The string makes a constant angle of 30° with the vertical. What is the tension in the string? (Use $g=10$ m/s².)
r30°m = 0.50 kg; L = 1.5 mLhorizontal circular path at constant height
  • A. 2.5 N
  • B. 3.0 N
  • C. 5.8 N
  • D. 10.0 N
The ball has no vertical acceleration, so $T\cos\theta=mg$. Therefore $T=mg/\cos30^\circ=(0.5)(10)/0.866=5.77$ N $\approx$ 5.8 N. Answer C. The horizontal component of tension supplies the inward force; it is not an additional “centripetal force.”
Q9. Medium 2.9
A 0.2 kg ball on a 0.8 m string is swung in a vertical circle. What is the minimum speed the ball must have at the top of the circle to keep the string taut? (Use $g = 10$ m/s².)
centerr = 0.80 m; m = 0.20 kgschematic; vectors labeled by their physical role
  • A. 2.0 m/s
  • B. 2.8 m/s
  • C. 4.0 m/s
  • D. 8.0 m/s
At minimum speed at top, tension = 0 (the threshold of losing tautness). Gravity alone provides centripetal force: $mg = mv^2/r$ → $v = \sqrt{gr} = \sqrt{10 \times 0.8} = \sqrt{8} = $ 2.83 m/s. Answer B. (At this speed, the ball is in free fall at the top — gravity provides exactly the centripetal force needed.)
Q10. Easy 2.4
Which of the following is an example of an object in translational equilibrium?
A: parachutestraight fall at terminal velocityB: carturning at constant speedC: tossed balltop of upward tossD: satelliteuniform circular orbitcompare velocity changes
  • A. A parachute falling at terminal velocity.
  • B. A car turning a corner at constant speed.
  • C. A ball at the top of its toss (instantaneously at rest).
  • D. A satellite in circular orbit at constant speed.
Translational equilibrium = $\Sigma F = 0$ = constant velocity (including $v = 0$). A: terminal velocity = constant velocity = equilibrium ✓. B: turning = acceleration (direction changing) → NO. C: at top of toss, $a = -g \neq 0$ → NO. D: circular orbit = centripetal acceleration → NO. Answer A.
Q11. Medium 2.7
Cube X (mass 2 kg) and Cube Y (mass 6 kg) slide on a rough surface with the same $\mu_k$. Cube Y has twice the contact area of Cube X. What is the ratio $F_{f,X} : F_{f,Y}$?
Cube Xmass 2 kgCube Ymass 6 kg; twice the contact areasame μₖ; same gravity; no additional vertical forces
  • A. 1 : 1
  • B. 1 : 3
  • C. 1 : 6
  • D. 1 : 9
$F_f = \mu_k F_N = \mu_k mg$. Same $\mu_k$ and $g$, so ratio = mass ratio = $m_X : m_Y = 2 : 6 = $ 1 : 3. Answer B. (Contact area does NOT affect friction — only $\mu$ and $F_N$ matter.)
Q12. Hard 2.5
An Atwood machine has a 4 kg mass on the left and a 10 kg mass on the right, connected by an ideal string over an ideal pulley. What is the acceleration of the system? (Use $g = 10$ m/s².)
4 kg10 kgone ideal string and ideal pulley
  • A. 3.0 m/s²
  • B. 4.3 m/s²
  • C. 6.0 m/s²
  • D. 10 m/s²
$a = \dfrac{(m_2 - m_1)g}{m_1 + m_2} = \dfrac{(10-4) \times 10}{4+10} = \dfrac{60}{14} = $ 4.3 m/s². Answer B. (10 kg goes down, 4 kg goes up. Tension would be $T = m_1(g+a) = 4(10+4.3) = 57.1$ N.)
Q13. Medium 2.3
A lander descends toward Mars at constant speed, attached to a parachute. Neglect air resistance on the lander itself. $\vec{F}_1$ = gravitational force of Mars on the lander. $\vec{F}_2$ = tension force of the parachute cord on the lander. Are $\vec{F}_1$ and $\vec{F}_2$ a Newton's third law pair?
Cord on landerF₂Mars on landerF₁constant downward velocity; distinguish force partners
  • A. Yes, because they are equal and opposite.
  • B. Yes, because they are both internal to the lander-parachute-Mars system.
  • C. No, because they are not equal in magnitude.
  • D. No, because the forces are not an interaction between the same two objects.
$F_1$ is between Mars and lander (gravity). $F_2$ is between parachute and lander (tension). They act on the same object (lander) but are between different pairs of objects. A 3rd law pair must be between the same two objects. Answer D. (The actual 3rd law pair of $F_1$ is "lander pulls Mars up"; the pair of $F_2$ is "lander pulls parachute down".) (Note: at constant speed, $F_1 = F_2$ in magnitude — but that doesn't make them a 3rd law pair.)
Q14. Medium 2.8
A block is held against a compressed horizontal spring on a frictionless surface. The block is released. Immediately after release, how do the spring force and the block's speed change?
compressed spring; frictionless surface; block released
  • A. Spring force increasing, speed increasing.
  • B. Spring force increasing, speed decreasing.
  • C. Spring force decreasing, speed increasing.
  • D. Spring force decreasing, speed decreasing.
As the block moves away, the spring decompresses (x decreases) → $F = kx$ decreases. But the spring is still pushing the block (force is still in the direction of motion), so the block speeds up (accelerates). Answer C. (The block keeps speeding up as long as the spring is pushing — even though the push gets weaker.)
Q15. Hard 2.7
Box C (3 kg) rests on Box D (5 kg) on a rough floor. A string pulls Box C to the right, and both boxes move together without slipping at constant speed. The friction between C and D is $f_{CD}$; between D and floor is $f_{DF}$. Now a 2 kg mass is placed on top of Box C, and the system again moves at constant speed. How do $f_{CD}$ and $f_{DF}$ change?
D: 5 kgC: 3 kgpulladd 2 kg on C; still no slip between boxes
  • A. $f_{CD}$ stays same, $f_{DF}$ stays same.
  • B. $f_{CD}$ stays same, $f_{DF}$ increases.
  • C. $f_{CD}$ increases, $f_{DF}$ stays same.
  • D. $f_{CD}$ increases, $f_{DF}$ increases.
The floor contact supports the entire stack, so adding the 2 kg mass increases the normal force on the floor and therefore increases the kinetic friction $f_{DF}$. For Box D to continue at constant speed, its horizontal forces must balance, so the static friction exerted on D by C must also increase to match the larger floor friction. Therefore both $f_{CD}$ and $f_{DF}$ increase. Answer D. The key idea is that static friction adjusts to the value required; it is not automatically equal to $\mu_sN$.
Q16. Hard 2.5
A sign hangs from two ropes. In Setup 1, Rope 2 makes a 45° angle with the ceiling. In Setup 2, Rope 2 makes a 60° angle with the ceiling (more vertical). Rope 1 is horizontal in both. Is the tension in Rope 1 ($T_{1B}$) in Setup 2 greater than, less than, or equal to $T_{1A}$ in Setup 1?
Rope 145°Setup 1Rope 160°Setup 2same sign; angle measured from horizontal ceiling
  • A. $T_{1B} = T_{1A}$ (Rope 1 is horizontal in both).
  • B. $T_{1B} > T_{1A}$ (steeper Rope 2 means more horizontal pull needed).
  • C. $T_{1B} < T_{1A}$ (steeper Rope 2 has smaller horizontal component).
  • D. Cannot be determined without the mass of the sign.
Vertical equilibrium: $T_2 \sin\theta = mg$ → $T_2 = mg/\sin\theta$. Horizontal: $T_1 = T_2 \cos\theta = mg \cos\theta / \sin\theta = mg / \tan\theta$. As $\theta$ increases (more vertical), $\tan\theta$ increases, so $T_1 = mg/\tan\theta$ decreases. Answer C. (When Rope 2 is more vertical, it supports more of the weight, so Rope 1 needs to pull less horizontally.)
Q17. Hard 2.6
Planet Alpha (mass $3m$) and Planet Beta (mass $m$) orbit a star (mass $M$). Alpha is at distance $2R$ from the star; Beta is at distance $R$. At the instant shown the three centers lie on one line and $M>3m$. Treat the bodies as point masses. What is the magnitude of the net gravitational force on Beta?
star MBeta mAlpha 3mRRinstant shown; M > 3m; bodies treated as point masses
  • A. $\dfrac{GmM}{R^2}$
  • B. $\dfrac{3Gm^2}{R^2}$
  • C. $\dfrac{Gm}{R^2}(M - 3m)$
  • D. $\dfrac{Gm}{R^2}\left(M - \dfrac{3m}{4}\right)$
Two forces on Beta: Star pulls Beta toward star (left, toward star): $F_{star} = \dfrac{GmM}{R^2}$. Alpha pulls Beta toward Alpha (right, toward Alpha): distance Beta-Alpha = $R$, so $F_{Alpha} = \dfrac{G \cdot m \cdot 3m}{R^2} = \dfrac{3Gm^2}{R^2}$. Net force = $F_{star} - F_{Alpha} = \dfrac{GmM}{R^2} - \dfrac{3Gm^2}{R^2} = \dfrac{Gm}{R^2}(M - 3m)$. Answer C.
Q18. Medium 2.1
A toolbox is placed on a uniform board whose own center of mass is at a frictionless midpoint pivot. When released, the right side goes down. What must be true about the toolbox's center of mass?
toolboxmidpoint pivotright side drops
  • A. The left side has more mass than the right side.
  • B. The right side has more mass than the left side.
  • C. The COM is to the left of the pivot.
  • D. The COM is to the right of the pivot.
An object tips toward its center of mass. If the right side goes down, the COM must be on the right side of the pivot. (Gravity pulls down on the COM; if COM is right of pivot, this creates a clockwise torque → right side tips down.) Answer D. The mass on either side need not be larger in total; the decisive information is the center-of-mass location relative to the pivot.
Q19. Easy 2.8
A spring hangs from the ceiling with relaxed length $L_0$. When a mass $m$ is attached, the spring stretches to length $L_0 + \Delta x$. If mass $m$ is replaced with mass $4m$, what is the new length of the spring at equilibrium?
Load mlength L₀ + ΔxLoad 4mnew length unknownsame ideal spring; equilibrium; relaxed length L₀
  • A. $\frac{1}{4}(L_0 + \Delta x)$
  • B. $L_0 + \frac{1}{4}\Delta x$
  • C. $4(L_0 + \Delta x)$
  • D. $L_0 + 4\Delta x$
Stretch $\Delta x = mg/k$. 4× mass → 4× stretch. The relaxed length $L_0$ doesn't change. New length = $L_0 + 4\Delta x$. Answer D. (C is wrong because you don't multiply $L_0$ by 4 — only the stretch.)
Q20. Hard 2.5
Block P (mass $m$) is attached to Block Q (mass $3m$) by a vertical string. Both are freely falling near Earth's surface. What is the acceleration of Block Q?
P: mQ: 3mfree fallideal connector; gravity is the only external force
  • A. Equal to $g$, because the other block is also in free fall and the tension is zero.
  • B. Equal to $g$, because the string pulls Q down with a force equal to Q's weight.
  • C. Less than $g$, because the string exerts an upward tension on Q.
  • D. Greater than $g$, because P pulls Q down.
Both blocks are in free fall — each accelerates at $g$ under gravity alone. Since they have the same acceleration, the string doesn't need to exert any force on either block. Tension = 0. Block Q accelerates at exactly $g$. Answer A. (Apply $\Sigma F = ma$ to Q: $3mg - T = 3m \cdot g$ → $T = 0$ ✓. An ideal string may remain straight with zero tension; it need not be described as slack.)
Q21. Medium 2.2
A block slides down a rough incline. Which set of arrows belongs on an AP-style free-body diagram of the block?
rough contactθv down slopeschematic scene; angle and labels specify the data
  • A. $mg\sin\theta$ down the plane, $mg\cos\theta$ into the plane, and friction up the plane.
  • B. Weight down, normal up, and a separate force $ma$ down the plane.
  • C. Weight vertically down, normal perpendicular to the surface, and friction up the plane.
  • D. Weight vertically down and a single resultant force down the plane.
Answer C. AP free-body diagrams show real forces, not components. Resolve $mg$ into components only after the FBD when writing equations. There is no separate $ma$ or “centripetal” force.
Q22. Medium 2.3
Two blocks are connected by one ideal string that passes over an ideal pulley. Which statement about the string tension is required by the ideal-string model?
block Ablock Bone ideal string and ideal pulley
  • A. The tension is larger on the heavier-block side.
  • B. The tension has the same magnitude at every point in that ideal string.
  • C. The tension is zero whenever the blocks accelerate.
  • D. The tension must equal the weight of each block.
Answer B. An ideal string has negligible mass and does not stretch, so its tension is the same throughout. That does not mean $T=mg$; accelerating blocks usually have $T\ne mg$.
Q23. Medium 2.4
A bus accelerates forward on a straight road. Which observer is most directly using an inertial reference frame for applying Newton's laws without introducing a fictitious force?
Bus velocityforwardBus accelerationforwardroadside observer approximates Earth as inertial
  • A. An observer standing on the roadside, approximating Earth as inertial.
  • B. A passenger sitting in the accelerating bus.
  • C. An observer rotating on a turntable inside the bus.
  • D. Any observer, because acceleration is always zero in the observer's own frame.
Answer A. A frame accelerating or rotating relative to an inertial frame is noninertial. In AP Physics 1, ordinary ground-based frames are normally treated as inertial unless stated otherwise.
Q24. Medium 2.6
A small test mass $m$ is placed at distance $r$ from the center of a spherical planet of mass $M$. The test mass is replaced by one of mass $3m$ at the same point. How does the gravitational field strength at that point change?
Source planetfixed mass MTest pointfixed center distance r; m → 3mtest mass has negligible influence on source
  • A. It triples.
  • B. It becomes one-third as large.
  • C. It is unchanged.
  • D. It becomes nine times as large.
Answer C. $g=F_g/m=GM/r^2$ is a property of the source mass and location. The gravitational force triples when the test mass triples, but the field strength does not.
Q25. Hard 2.6
A sealed capsule and a student inside it are both in free fall near Earth. The student stands on a scale fixed to the floor of the capsule. Which statement is correct?
a = g downscale reads support force
  • A. The scale reads $mg$ because gravity still acts.
  • B. Gravity becomes zero, so the scale reads zero.
  • C. The scale reads more than $mg$ because the capsule accelerates.
  • D. The scale reads zero even though gravity is nonzero.
Answer D. Apparent weight is the normal force. In free fall, gravity is the only force needed to accelerate the student at $g$, so $N=0$. “Weightless” means zero apparent weight, not zero gravitational force.
Q26. Hard 2.9
A car moves counterclockwise around a circular track and is speeding up. At the rightmost point of the circle, which direction best describes its acceleration?
centervspeed increasing; counterclockwiseschematic; vectors labeled by their physical role
  • A. Straight left only.
  • B. Up and left: inward centripetal plus forward tangential components.
  • C. Straight up only.
  • D. Down and right, opposite the velocity.
Answer B. At the rightmost point, inward is left. Because the car is speeding up while moving upward, tangential acceleration is upward. The net acceleration is their vector sum.
Q27. Medium 2.9
On the same flat circular track, a car's speed increases from $v$ to $1.5v$. If static friction remains sufficient, by what factor does the required inward friction force change?
Run 1speed vRun 2speed 1.5vsame mass and radius; static friction sufficient
  • A. $1.5$
  • B. $2.0$
  • C. $2.25$
  • D. $3.0$
Answer C. $F_{in}=mv^2/r$, so the factor is $(1.5)^2=2.25$. The friction force is not automatically $\mu_sN$; it supplies the needed value up to its maximum.
Q28. Hard 2.9
Two frictionless banked curves have the same banking angle. Curve B has twice the radius of Curve A. What is the ratio of the design speeds $v_B/v_A$?
Curve Aradius RCurve Bradius 2Rsame θ and gravity; each car at its design speed
  • A. $1$
  • B. $\sqrt{2}$
  • C. $2$
  • D. $4$
For a frictionless bank, $\tan\theta=v^2/(rg)$. With the same $\theta$, $v\propto\sqrt r$. Doubling $r$ multiplies the design speed by $\sqrt2$. Answer B.
Q29. Hard 2.9
Two satellites move in circular orbits around the same planet. Satellite B has orbital radius $2R$ while Satellite A has radius $R$. What is $T_B/T_A$?
MA: RB: 2Rorbital radii measured from central mass; paths to scale
  • A. $\sqrt2$
  • B. $2$
  • C. $4$
  • D. $2\sqrt2$
For circular orbits around the same central mass, $T^2\propto R^3$, so $T\propto R^{3/2}$. Therefore $T_B/T_A=2^{3/2}=2\sqrt2$. Answer D.
Q30. Medium 2.9
A satellite is in a circular orbit and no forces other than gravity act on it. Which statement is correct?
Msatelliteradius rone circular orbit; radius from the center
  • A. Gravity itself is the net inward force that produces the centripetal acceleration.
  • B. Gravity balances a separate centripetal force.
  • C. The satellite has zero acceleration because its speed is constant.
  • D. An outward force equal to gravity must act so the orbit radius stays constant.
Answer A. “Centripetal” describes the direction/function of the net force; it is not an extra force. In a circular gravitational orbit, $F_g=mv^2/r$.

Free Response Questions

AP routine training
These eight questions are original PHYSICS CREST scenarios. They train the current four AP Physics 1 free-response routines without copying Progress Check wording. Use a calculator only when useful, begin derivations from a fundamental principle, and treat every “justify” as qualitative reasoning beyond equations.
FRQ 1. Hard 2.5 · 2.7 MR · 10 points
Warehouse tow system. Cart A of mass $m$ is connected by an ideal string to Cart B of mass $2m$ on a horizontal floor. A horizontal external force $F$ pulls the leading Cart A to the right; Cart B follows behind. Cart A rolls with negligible resistance; Cart B slides with coefficient of kinetic friction $\mu_k$. Both move to the right.

(a) [2] Draw and label the forces on Cart B. (b) [3] Starting with Newton's second law, derive the acceleration of the two-cart system. (c) [2] Derive the tension in the string. (d) [2] For $m=4.0$ kg, $F=60$ N, $\mu_k=0.25$, and $g=10$ m/s², calculate $a$. (e) [1] Without recalculating, predict how $a$ changes if $\mu_k$ increases and justify.
B: 2mA: mFA rolls; B slides right; force F pulls A right
(a) 2 points
1 pt — $2mg$ downward and $N$ upward.
1 pt — tension $T$ right and kinetic friction $f_k$ left; no components or $ma$ arrow.
(b) 3 points
1 pt — choose {A+B}: $F-f_k=(3m)a$.
1 pt — $f_k=\mu_kN=\mu_k(2mg)$.
1 pt — $\boxed{a=\dfrac{F-2\mu_kmg}{3m}}$.
(c) 2 points
1 pt — for B: $T-2\mu_kmg=2ma$.
1 pt — $\boxed{T=2ma+2\mu_kmg}$ (equivalent substituted form accepted).
(d) 2 points
1 pt — friction $=0.25(80)=20$ N; net system force $40$ N.
1 pt — total mass $12$ kg, so $\boxed{a=3.33\ \mathrm{m\,s^{-2}}}$.
(e) 1 point
1 pt — $a$ decreases because larger kinetic friction reduces the net external force while total mass is unchanged.

Total: 10 points.
FRQ 2. A* 2.2 · 2.9 MR · 10 points
Frictionless banked test track. A small car of mass $m$ travels at constant speed around a circular track of radius $R$. The road is banked at angle $\theta$ and friction is negligible.

(a) [2] Draw the forces on the car. (b) [4] Starting with Newton's second law, derive the speed for which the car follows the circle without sliding. (c) [2] Calculate the design speed for $R=25$ m, $\theta=37^\circ$, $g=10$ m/s², using $\tan37^\circ\approx0.75$. (d) [2] A second track has the same bank angle but radius $4R$. Predict its design speed relative to the first and justify.
θmass m; radius R; bank θinwardcross-section; circle center lies to the left
(a) 2 points
1 pt — weight $mg$ vertically downward.
1 pt — normal force perpendicular to the road; no “centripetal force” arrow.
(b) 4 points
1 pt — vertical: $N\cos\theta=mg$.
1 pt — inward: $N\sin\theta=mv^2/R$.
1 pt — divide equations: $\tan\theta=v^2/(Rg)$.
1 pt — $\boxed{v=\sqrt{Rg\tan\theta}}$.
(c) 2 points
1 pt — $v^2=(25)(10)(0.75)=187.5$.
1 pt — $\boxed{v\approx13.7\ \mathrm{m\,s^{-1}}}$.
(d) 2 points
1 pt — $v\propto\sqrt R$ at fixed $\theta$.
1 pt — radius $4R$ gives speed $2v$.

Total: 10 points.
FRQ 3. Hard 2.7 · 2.8 TBR · 12 points
Spring cart with sliding friction. A block of mass $m$ is attached to a horizontal spring of constant $k$ on a rough surface. Let $x=0$ be the spring's relaxed position. At the instant considered, the block is at $x>0$ and moving to the right; kinetic friction has constant magnitude $f_k$.

(a) [3] Draw an AP-style FBD. (b) [3] Derive $F_{net,x}(x)$ while the block is moving right. (c) [3] On paper, sketch $F_{spring}$ and $F_{net,x}$ versus $x$ for $x>0$ and identify their slopes/intercepts. (d) [3] Predict how the $F_{net,x}$ graph changes if $\mu_k$ increases, and justify using your representation.
x > 0 from relaxed position; v right; rough floor
(a) 3 points
1 pt — $mg$ down and $N$ up.
1 pt — spring force left (toward $x=0$).
1 pt — kinetic friction left because the block slides right relative to the fixed surface.
(b) 3 points
1 pt — choose +x right; $F_s=-kx$.
1 pt — $f_k=\mu_kmg$ and is negative while moving right.
1 pt — $\boxed{F_{net,x}=-kx-\mu_kmg}$.
(c) 3 points
1 pt — $F_s$ is a line through the origin with slope $-k$.
1 pt — $F_{net,x}$ is parallel with the same slope $-k$.
1 pt — its vertical intercept is $-\mu_kmg$.
(d) 3 points
1 pt — larger $\mu_k$ makes the intercept more negative.
1 pt — slope remains $-k$.
1 pt — explain: friction magnitude increases by a constant amount while spring law is unchanged.

Total: 12 points.
FRQ 4. A* 2.5 · 2.6 TBR · 12 points
Elevator scale translation. A student of mass $m$ stands on a scale in an elevator. The elevator's acceleration (with $0\lt a_0\lt g$) is upward at $+a_0$ from $0$ to $t_1$, zero from $t_1$ to $2t_1$, and downward at $-a_0$ from $2t_1$ to $3t_1$.

(a) [2] Draw the forces on the student. (b) [3] Derive scale reading $N$ in terms of $m$, $g$, and elevator acceleration $a$. (c) [4] Sketch $N$ versus time for the full interval and label the three levels. (d) [3] Suppose the elevator is moving downward during the first interval while its acceleration remains upward. Explain whether the scale graph changes and what happens to the student's speed.
0123-101a / a₀t / t₁
(a) 2 points
1 pt — weight $mg$ down.
1 pt — scale normal force $N$ up.
(b) 3 points
1 pt — +up: $N-mg=ma$.
1 pt — rearrange.
1 pt — $\boxed{N=m(g+a)}$.
(c) 4 points
1 pt — first level $m(g+a_0)$.
1 pt — middle level $mg$.
1 pt — final level $m(g-a_0)$.
1 pt — correct step timing at $t_1$ and $2t_1$.
(d) 3 points
1 pt — scale graph is unchanged because $N$ depends on acceleration, not velocity direction.
1 pt — velocity is downward but acceleration upward, so the student/elevator slows down.
1 pt — explicitly distinguish velocity from acceleration.

Total: 12 points.
FRQ 5. Hard 2.7 LAB · 10 points
Determine $\mu_k$ without trusting one trial. Available: a wooden block of known mass, several known masses, a level board, force sensor, and meterstick. Design an experiment to determine the coefficient of kinetic friction between block and board using a linear graph.

(a) [4] Describe a repeatable procedure, including what you vary, what you measure, and how you ensure the measured pulling force equals kinetic friction. (b) [2] State the graph and how $\mu_k$ is obtained. (c) [2] Give two uncertainty-reduction strategies. (d) [2] If the best-fit line has a significant positive vertical intercept, give one plausible experimental reason and explain the effect.
Apparatusblock; board; force sensorAdditional equipmentknown masses; meterstickdesign a graph method; no graph or procedure supplied
(a) 4 points
1 pt — add known masses to vary total mass/normal force.
1 pt — pull horizontally so $N=mg$ for the block+added masses.
1 pt — move at approximately constant speed and record steady force-sensor reading.
1 pt — collect multiple $(N,f_k)$ pairs over a useful range.
(b) 2 points
1 pt — plot $f_k$ vertically versus $N$ horizontally.
1 pt — slope $=\mu_k$.
(c) 2 points
1 pt each — any two sound strategies: repeat/average, zero/calibrate sensor, long steady-speed interval, broad range of normal forces, best-fit line rather than two points.
(d) 2 points
1 pt — plausible cause such as sensor zero offset or a small additional constant resistance.
1 pt — explains it adds approximately the same force to every trial, shifting the line upward.

Total: 10 points.
FRQ 6. A* 2.5 LAB · 10 points
Determine an unknown cart mass. A cart rolls on a nearly frictionless track. Students have a force sensor and a motion sensor but no balance. They can apply different approximately constant horizontal forces and measure the resulting acceleration.

(a) [4] Describe a procedure that would determine the cart's inertial mass from a linear graph. (b) [2] State two valid choices of graph and how mass is obtained from each. (c) [2] Explain why several force values are better than one calculation $m=F/a$. (d) [2] The best-fit $F_{applied}$ versus $a$ line has a positive intercept. Explain what this suggests about the track and how the slope should still be interpreted.
cart: unknown mmotionsensormeasured Fmotion sensor observes cart without a mechanical link
(a) 4 points
1 pt — apply several measured horizontal forces.
1 pt — use motion sensor to determine acceleration for each force.
1 pt — keep cart/configuration unchanged and collect multiple trials.
1 pt — create a best-fit linear graph based on $F_{net}=ma$.
(b) 2 points
1 pt — plot $F$ vs $a$: slope is $m$.
1 pt — or plot $a$ vs $F$: slope is $1/m$, so $m=1/\text{slope}$.
(c) 2 points
1 pt — reduces influence of random measurement uncertainty.
1 pt — reveals systematic offsets/nonlinearity instead of hiding them in one ratio.
(d) 2 points
1 pt — positive intercept suggests a roughly constant opposing force such as rolling resistance/track friction or sensor offset.
1 pt — the slope still represents inertial mass if the opposing force is approximately constant.

Total: 10 points.
FRQ 7. Hard 2.6 · 2.9 QQT · 8 points
Two circular satellite orbits. Probe A moves in a circular orbit of radius $R$ around a planet of mass $M$. Probe B orbits the same planet at radius $4R$.

(a) [2] Without equations, claim whether B's orbital speed is greater than, less than, or equal to A's and justify physically. (b) [3] Starting with Newton's second law and universal gravitation, derive the circular-orbit speed $v(R)$. (c) [1] Use your expression to determine $v_B/v_A$. (d) [2] Predict $T_B/T_A$ and justify using $T=2\pi R/v$ together with your speed result.
MA: RB: 4Rorbital radii measured from central mass; paths to scale
(a) 2 points
1 pt — B is slower.
1 pt — gravity weakens with the square of distance, faster than the change in path curvature can compensate at the same speed. A circular orbit farther away therefore needs a lower speed.
(b) 3 points
1 pt — $GMm/R^2=mv^2/R$.
1 pt — cancel $m$ and one $R$.
1 pt — $\boxed{v=\sqrt{GM/R}}$.
(c) 1 point
1 pt — $v_B/v_A=\sqrt{R/(4R)}=\boxed{1/2}$.
(d) 2 points
1 pt — $T\propto R/v$.
1 pt — radius is $4\times$ and speed is $1/2\times$, so $T_B/T_A=\boxed{8}$.

Total: 8 points.
FRQ 8. A* 2.7 · 2.9 QQT · 8 points
Flat curve at the friction limit. A car of mass $m$ travels at speed $v$ around a flat curve of radius $R$. The tires do not slip. The coefficient of static friction is $\mu_s$. A student claims: “A heavier car with the same tires and the same speed is more likely to skid because it needs more centripetal force.”

(a) [2] State whether the claim is correct and justify qualitatively. (b) [3] Derive the maximum speed before slipping. (c) [1] Explain mathematically why mass cancels. (d) [2] If both $R$ and $\mu_s$ are doubled, by what factor does $v_{max}$ change? Justify.
centerm; v; R; static coefficient μₛschematic; vectors labeled by their physical role
(a) 2 points
1 pt — claim is incorrect within the ideal model.
1 pt — both the required inward force $mv^2/R$ and maximum static friction $\mu_smg$ scale with mass, so the margin to slipping is unchanged.
(b) 3 points
1 pt — at the threshold, $\mu_smg=mv^2/R$.
1 pt — cancel $m$ and rearrange.
1 pt — $\boxed{v_{max}=\sqrt{\mu_sgR}}$.
(c) 1 point
1 pt — both sides are directly proportional to $m$.
(d) 2 points
1 pt — $v_{max}\propto\sqrt{\mu_sR}$.
1 pt — doubling each gives factor $\sqrt{4}=\boxed{2}$.

Total: 8 points.
Ready for independent testing?
When the worked solutions no longer surprise you, move to Exam Arena. Arena questions use different scenarios and do not reveal reasoning until after an attempt.