Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.
Turn every pressure problem into a clean ratio or liquid-column story: identify the force, total contact area, density and vertical depth—then let the units guard your method.
One idea, two pressure stories: contact force over area and liquid weight with depth.
1
Force concentration
Pressure
PressurePerpendicular force divided by area.
The pascal is N/m².
A smaller area gives greater pressure for the same force; a larger area spreads it.
The relevant area is the surface supporting that force.
Pressure is defined as force per unit area. A large force is not automatically a large pressure—the area carrying that force matters just as much.
Read the perpendicular force and the complete area touching the surface.
$p=F/A$
Compare pressure by calculating force divided by area for each case.
Force
Use the force perpendicular to the surface. For an object resting horizontally, this is usually its weight when no other vertical force changes the contact force.
Area
Use the total area actually touching the surface, expressed in m² for a pressure in pascals.
Use only the labelled quantities required by the question.
Meaning mnemonicPRESS = PUSH ÷ PATCH
The push is the force; the patch is the contact area. More push or a smaller patch gives more pressure.
Interactive · Pressure Calculator
Force divided by area
Definition mark: write “force per unit area.” “How hard something pushes” is intuition, not the required definition.
Mass is not force: if mass is supplied, first find weight using $W=mg$—unless the contact force is given directly.
2
One relationship, three unknowns
Pressure calculations
Cover the required symbol, then use the remaining relationship.
$p=F/A$
Find pressure from force and total contact area.
$F=pA$
Find the force caused by a known pressure over an area.
$A=F/p$
Find the contact area needed for a target pressure.
Read the perpendicular force and the complete area touching the surface.
Worked: pressure to force
Convert $2.4 kPa=2400 Pa$.
$F=pA=(2400)(0.035)=84 N$.
A unit sense-check agrees: $(N/m²)(m²)=N$.
Use only the labelled quantities required by the question.
Method mnemonicD-E-S-U-S
Data → Equation → Subject → Units → Sense-check. Rearrange symbolically before entering values.
Quick Check · A pressure of 18 kPa acts on 0.025 m². Find the force.
450 N. Convert $18 kPa=18000 Pa$, then $F=pA=(18000)(0.025)$.
kPa trap: multiply by 1000 before using pascals: $32 kPa=32000 Pa$.
Unit line: match the pressure unit to the area used. With area in m², use Pa (= N/m²). If a question deliberately keeps area in cm², N/cm² is also valid. Never mix the area and pressure units.
3
The most common source of lost marks
Contact area and units
Standing on two identical soles uses their combined contact area.
Turning a block changes area but not its weight.
Convert squared lengths correctly: 1 cm² = 0.0001 m².
A length in centimetres is not itself an area.
A sharp cutting edge and a broad snowshoe exploit opposite choices of contact area.
Squared units need squared conversion factors.
There are two safe conversion routes. Convert each length to metres and then calculate area, or calculate the area first and convert the squared unit with its squared factor.
Convert lengths to metres before multiplying, or convert the completed squared area.
Worked: dimensions in centimetres
$20 cm=0.20 m$ and $10 cm=0.10 m$.
$A=(0.20)(0.10)=0.020 m²$.
For a 160 N weight, $p=160/0.020=8000 Pa$.
Use the sum of all areas actually touching the ground.
Count how many feet, legs or pads are touching.
Calculate the area of one contact.
Multiply by the number of contacts.
Convert the total to m².
Divide the perpendicular force by that total.
Interactive · Squared-Unit Converter
Convert an area to m²
Squared-unit trap: $1 m=100 cm$, but $1 m²=10000 cm²$. Never divide cm² by only 100.
Contact trap: a four-legged table uses four foot areas, not the whole tabletop area and not only one foot.
4
Explain with a three-link chain
Pressure in everyday situations
same force + larger area → lower pressure · same force + smaller area → higher pressure
Broad tracks spread the load across a large area.A wide board increases the supported contact area.A wide foundation spreads a structure’s weight.A wide handle spreads a force over the hand.
Explanation mnemonicS-A-P
Same force or weight → Area becomes larger/smaller → Pressure becomes lower/higher. State every link.
Design purpose
Area choice
Pressure result
avoid sinking or marking
large tracks, pads, foundations or boards
lower pressure
cut or pierce efficiently
narrow edge or small point
higher pressure
make a grip comfortable
wide padded handle
lower pressure on the hand
Interactive · Explanation Builder
Same weight: which change lowers pressure?
Half-answer trap: “because it is wider” does not earn the complete explanation. Link the larger area to smaller force per unit area and therefore lower pressure.
Keep the force story honest: a wide tyre does not reduce the vehicle’s weight; it changes the area over which that weight acts.
Pause · explain it yourself
Why does a drawing pin have a broad head and a sharp point?
Compare, then improve
The head lowers pressure on the finger; the point raises pressure on the material for the same transmitted force.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
5
Same object, different face
Changing the contact face
Compare force divided by each face area.
For one block on a horizontal surface, the contact force is unchanged when the block is turned. Pressure is greatest on the smallest face and smallest on the largest face.
Use the stated face area for each orientation.
Worked: ratio before arithmetic
Face B has one quarter of face A’s area. With the same force, face B produces four times the pressure.
$p_A=240/0.080=3000 Pa$ and $p_B=240/0.020=12000 Pa$.
Compare pressure by calculating force divided by area for each case.
Interactive · Face Comparator
Same force on two faces
Orientation shortcutSMALL FACE → BIG p
At fixed weight, pressure is inversely proportional to contact area.
Dimensions trap: select the two dimensions of the face touching the surface—not the height of the upright object unless it belongs to that face.
6
Depth and density
Pressure in a liquid
A liquid’s pressure increases with depth because more liquid lies above the level.
Greater density gives a heavier overlying column for the same volume.
Use vertical depth below the surface, not a sloping wall length.
Measure every vertical depth from the free surface.
Depth rule
In the same liquid, a vertically deeper point has a greater pressure because a taller liquid column lies above it.
Density rule
At the same depth, a denser liquid gives a greater pressure because the liquid column has more mass and weight per unit volume.
Rank points using vertical depth below the free surface, not the amount of liquid drawn above them.
Pressure at one point in a stationary liquid acts equally in all directions. However, the top and bottom of a large object are at different depths, so their pressure values are not exactly equal.
Container shape and total volume do not change pressure at equal depth in the same liquid.
Container shape, base width and total liquid volume do not determine the pressure change at a point. The controlling variables are density, gravitational field strength and vertical depth.
Liquid pressure increases with depth, so a retaining wall must withstand a larger pressure near its base.
Interactive · Liquid Rule Check
Same liquid: what definitely raises pressure?
Dam explanation: deeper water produces greater pressure near the bottom, so the wall must withstand a larger force per unit area there.
Same-direction wording: say “pressure at a point acts in all directions.” Do not claim that every point on a submerged object has the same pressure.
Pause · explain it yourself
Two open containers have the same liquid depth but different widths. Compare bottom pressure.
Compare, then improve
Equal, if their surface pressures are equal. Density, g and depth determine the increase.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
7
Supplement calculation
Calculating liquid pressure
The increase between two levels is Δp = ρgΔh.
For the same stationary connected liquid and surface pressure, pressure at equal depth is equal even in containers with different shapes.
This is a pressure increase due to the liquid; total pressure also includes pressure at the surface when that is required.
$Δp=ρgΔh$
For comparisons at the same g, compare the product density × vertical depth.
Symbol
Meaning
SI unit
$Δp$
pressure change caused by the liquid column
Pa
$ρ$
liquid density
kg/m³
$g$
gravitational field strength
N/kg
$Δh$
vertical depth change
m
For constant density and g, pressure change is directly proportional to depth.
Worked: direct calculation
For water at $3.2 m$, with $ρ=1000 kg/m³$ and $g=10 N/kg$:
$Δp=(1000)(10)(3.2)=32000 Pa=32.0 kPa$.
Use the vertical depth, not the sloping path length.
Depth mnemonicV FOR VERTICAL
$Δh$ is a vertical depth below the free surface, or the vertical separation between two points. It is not a diagonal cable, pipe or swimming path length.
Use only the labelled quantities required by the question.
Interactive · Hydrostatic Calculator
Density × g × vertical depth
Hydrostatic wording: $ρgΔh$ gives the change in pressure caused by the liquid column. In Topic 1.8 calculations, label this result $Δp$ and do not add an unrelated pressure.
Pause · explain it yourself
What happens to liquid pressure increase at a fixed depth if density doubles?
Compare, then improve
It doubles with g and depth fixed.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
8
Unfamiliar contexts become products
Comparing pressures
A block-on-floor problem usually needs p = F/A; a liquid-depth difference usually needs Δp = ρgΔh.
Draw a simple labelled sketch before choosing an equation.
State controlled quantities when explaining change.
Halving area doubles pressure only at constant force.
Doubling depth doubles the liquid’s pressure increase only for unchanged density and g, and does not generally double total absolute pressure.
If a question asks for a change between two submerged positions, first subtract depths rather than using the final depth alone.
When $g$ is the same, compare the product $ρΔh$. The larger product gives the larger liquid pressure change.
For comparisons at the same g, compare the product density × vertical depth.
Worked: density and depth both change
Tank R: $ρh=(1200)(1.5)=1800$.
Tank S: $ρh=(800)(2.0)=1600$.
Therefore $Δp_R/Δp_S=1800/1600=1.125$.
A pressure change acting over a small area gives force using F = pA.
If a pressure acts approximately uniformly over a small panel, rearrange $p=F/A$ to obtain $F=pA$. State clearly that this force is calculated from the pressure change caused by the liquid column.
Pressure change is proportional to gravitational field strength when density and depth are fixed.Use only the labelled quantities required by the question.
Interactive · ρh Comparator
Compare two liquids at the same g
Ratio method: write the two $ρh$ products before deciding. Depth alone cannot settle the comparison when density also changes.
Do not add unrelated pressures: a machine’s contact pressure on a floor and a liquid pressure inside the machine act at different surfaces and are not a single total.
9
Alternative to Practical
Design a pressure experiment that changes one cause at a time
Measure vertical depth from the free surface to the centre of the pressure sensor.
Direct method: pressure sensor against depth
Secure the tank and clamp; keep electrical equipment dry.
Zero the pressure sensor at the free surface.
Measure vertical depth to the centre of the sensing element.
Use at least six well-spaced depths and wait for stable readings.
Repeat, calculate means and record spread.
Plot mean $Δp$ against $h$ with units.
For constant density and g, pressure change is directly proportional to depth.
Graph meaning
A straight line through or near the origin supports $Δp∝h$. Its gradient is $ρg$, so $ρ=gradient/g$.
Validity checks
Keep the same liquid and temperature, measure from the surface, avoid wall/base contact, check zero drift and use a wide depth range.
Use only teacher-prepared holes; range is a proxy, not a direct pressure measurement.
Proxy warning: water-jet range can show a trend but is not a direct pressure measurement. Range also depends on hole shape, falling height and changing water level.
$h$/m
$Δp_1$/Pa
$Δp_2$/Pa
mean $Δp$/Pa
0.20
1960
1980
1970
0.40
3910
3940
3925
0.60
5880
5860
5870
Safety: use stable modest-size apparatus, teacher-prepared holes only, collect water in a tray, wipe spills promptly and keep cables/cameras away from water.
Evaluation quality: name the exact problem, its likely effect and a specific improvement. “Human error” without a mechanism earns little.
10
Last-minute examiner sheet
Pressure Master Sheet
Cover the required symbol, then use the remaining relationship.
Squared units need squared conversion factors.
Equation set
$p=F/A$ · $F=pA$ · $A=F/p$
$Δp=ρgΔh$
Units: pressure Pa, force N, area m², density kg/m³, $g$ N/kg, depth m.
Use the vertical depth, not the sloping path length.Container shape and total volume do not change pressure at equal depth in the same liquid.
Solid-pressure route
Identify perpendicular force.
Find total touching area.
Use an area unit that matches the required pressure unit.
Choose/rearrange $p=F/A$.
Attach Pa, N/m² or N/cm² as appropriate and sense-check.
Liquid-pressure route
Choose the free-surface reference.
Mark vertical $Δh$.
Use the correct density.
Calculate $ρgΔh$.
Label the result as pressure change $Δp$.
Final memory stripPUSH ÷ PATCH · ρgVERTICAL
For solids: force over total contact area. For liquids: density × gravitational field strength × vertical depth.
Six final traps: mass instead of weight · one foot instead of total area · unsquared conversion · diagonal depth · judging only density or only depth · using sloping distance instead of vertical depth.
Final Check · Water and oil are at different depths. What comparison should you make first?
Compare $ρh$ for each liquid when $g$ is the same. The larger $ρΔh$ product gives the larger pressure change when $g$ is the same.
Topic 1.8 complete
You can now define, calculate, explain, compare and investigate pressure without losing marks to area, depth or wording.