Skip to lesson
PHYSICS CREST · 2.2.2–2.2.3Internal energySHCExperimentsState changesEvaporation
1

2.2.2 & 2.2.3 · Specific Heat Capacity & State Changes

Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.

internal energy · SHC · melting · boiling · evaporation

Internal energy and temperature

  • Temperature relates to average particle kinetic energy.
  • Internal energy includes particle kinetic energy and interaction-related potential energy.
  • A temperature rise increases internal energy, but internal energy can also increase during melting or boiling at constant temperature.

When the temperature of an object rises, its internal energy increases. A higher temperature means a greater average kinetic energy of its particles.

Exam trap
Temperature is linked to average kinetic energy. Equal temperature does not mean equal total internal energy.
Temperature and average particle kinetic energyTemperature and average particle kinetic energylower temperaturelower average kinetic energyhigher temperaturehigher average kinetic energy
Use only the information shown.
Quick Check 1
A metal block is heated without changing state. What happens to its internal energy and average particle kinetic energy?
Both increase.
2

Specific heat capacity

  • Specific heat capacity is energy needed per kilogram per unit temperature rise.
  • Use ΔE = mcΔθ without a state change.
  • Its unit is J/(kg °C) or J/(kg K).
  • Use the temperature difference, not final temperature.
  • Larger c means more energy is needed for the same mass and rise.
  • Keep energy in joules distinct from power in watts.
Definition
Specific heat capacity, c, is the energy required to raise the temperature of 1 kg of a substance by 1 °C (or 1 K), without a change of state.
c = ΔE / (m Δθ)    ⇔    ΔE = m c Δθ
SymbolMeaningUnit
ΔEenergy transferredJ
mmasskg
cspecific heat capacityJ/(kg °C)
Δθtemperature change°C or K
Memory hook
E = m c Δθ.

Worked example

A 0.50 kg block with c = 900 J/(kg °C) warms from 20 °C to 35 °C. Δθ = 15 °C, so ΔE = 0.50 × 900 × 15 = 6750 J.

Quick Check 2
A 0.30 kg sample absorbs 5400 J and warms by 20 °C. Find c.
c = 5400/(0.30 × 20) = 900 J/(kg °C).

Pause · explain it yourself

Equal masses receive equal energy with no losses. Which warms more: larger c or smaller c?

Your turn · Extended: find energy for m = 0.20 kg, c = 900 J/(kg °C), ΔT = 10 °C.

Decimals and scientific notation are accepted. Compatible units are accepted.

3

Measuring specific heat capacity

  • Measure sample mass, initial temperature, energy input and final temperature.
  • Electrical input can be measured or found from IVt or Pt under constant conditions.
  • Calculate c = input energy/(mass × temperature rise).
  • Insulate a block and ensure good heater and thermometer contact.
  • For a liquid, use a lid where suitable and stir gently to make temperature uniform.
  • Some input warms the container, heater and surroundings.
  • Assigning all of it to the sample tends to overestimate c.
  • Repeats do not eliminate this systematic error, and longer heating can increase energy loss.
SHC experiment — solidmeasuremass mrecordinitial temperaturesupplymeasured energy ΔErecordfinal temperature
Insulate the block and ensure good thermal contact with the heater and temperature sensor.

Solid

  1. Measure the block mass.
  2. Insert a heater and temperature sensor.
  3. Insulate the block and record the initial temperature.
  4. Supply a measured amount of electrical energy, preferably using a joulemeter.
  5. Record the final temperature and calculate Δθ.
  6. Use c = ΔE/(mΔθ).

Liquid

  1. Find liquid mass by subtracting empty-container mass.
  2. Use an immersion heater and temperature sensor.
  3. Insulate, use a lid and stir gently.
  4. Measure energy transferred and temperature rise.
  5. Calculate c.
Error direction
If energy that warms the container or escapes to the surroundings is wrongly counted as energy gained by the sample, the calculated c is usually too high.
Quick Check 3
Why is insulation used?
To reduce energy transfer to the surroundings so the measured energy is closer to the energy gained by the sample.

Pause · explain it yourself

Why stir a liquid during this experiment?

4

Melting, boiling and condensation

  • During melting or boiling of a pure substance at fixed pressure, energy is supplied without a temperature rise.
  • Energy changes arrangement and separation rather than average kinetic energy.
  • Condensation and solidification transfer energy out.
  • Water melts at 0 °C and boils at 100 °C at standard atmospheric pressure.
Heating curve for pure water at standard atmospheric pressuretime / energy suppliedtemperature / °Cmeltingboiling0 °C100 °C
During melting and boiling, energy is supplied while temperature stays constant.

During melting or boiling of a pure substance, energy can be transferred while the temperature stays constant. The energy changes the particle arrangement/separation rather than increasing average kinetic energy.

ChangeDirectionParticle description
meltingsolid → liquidparticles leave fixed positions and move past one another
boilingliquid → gasparticles become widely separated; bubbles form throughout
condensationgas → liquidparticles become close together but still move past one another
solidificationliquid → solidparticles become ordered and vibrate about fixed positions
Water at standard atmospheric pressure
melting point = 0 °C · boiling point = 100 °C
Current topic boundary
Explain the energy transfer during a state change; no phase-change energy equation is required in this topic.
Quick Check 4
Why can temperature stay constant during melting while energy is supplied?
The energy changes the state/particle arrangement instead of increasing average kinetic energy.
A pure substance melts at constant pressure while energy is supplied. What can happen?

5

Evaporation and cooling

  • Evaporation occurs at the surface over a range of temperatures: more-energetic particles escape, reducing the remaining average kinetic energy and cooling the liquid.
  • Higher temperature, larger surface area and greater air movement increase evaporation.
  • Boiling occurs throughout the liquid, with vapour bubbles, at its boiling temperature.
  • No numerical latent-heat equation is required in this section.
Evaporation from a liquid surfacemore energetic particle escapes
Evaporation occurs at the surface and can occur below the boiling point.

Evaporation occurs at the surface. More energetic particles are more likely to escape. Their escape can lower the average kinetic energy of the particles left behind, so the liquid cools.

ChangeEffect on evaporation
higher temperaturefaster
larger exposed surface areafaster
greater air movementfaster

Boiling vs evaporation

EvaporationBoiling
surface onlythroughout the liquid
can occur below boiling pointoccurs at boiling temperature for the stated pressure
no bubbles requiredvapour bubbles form throughout the liquid
Quick Check 5
Why does moving air over wet skin make it feel cooler?
Moving air removes vapour near the skin, increasing evaporation. Energy is transferred from the skin to the evaporating water, so the skin cools.

Pause · explain it yourself

Can evaporation cool liquid even while energy arrives from the surroundings?

6

Thermal-properties review

Memory strip
SHC: E = mcΔθ · State change: energy without Δθ · Evaporation: surface + energetic escape + cooling
·