PHYSICS CREST
Physics

Topic 4.3 · Electric Circuits

Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.

Read the symbols, trace nodes and complete paths, apply current and p.d. conservation, then reduce the network before calculating.

20 circuit componentsSeries ↔ parallelDivider logicCircuit-building ATP
one pathsame two nodesPATHS → NODES → LAWS
One path means series; components connected across the same two nodes are parallel.
1
Trace before calculating

Circuit paths and junctions

one pathsame two nodes
Series is one unbranched path; parallel components share the same two end nodes.
R₁L6 V
The two coloured rails are nodes: every point on one ideal connecting wire has the same potential.
Switch states change the conducting topology. Redraw only the complete paths before reasoning.

Start every circuit question with a finger-trace. Move from one source terminal, through conducting components, and back to the other terminal. A path broken by an open switch carries no steady current.

What proves that two components are parallel?
WordExaminer meaningReading move
node / junctionconnected conductor at one potential; branches may meetmark every continuous wire as one node
branchone route between two junctionstrace its current separately
seriessame unbranched pathsame current
parallelsame pair of end nodessame p.d.
bypass / shortvery low-resistance route around a componentcomponent p.d. becomes approximately zero
MnemonicPATH → NODE → BRANCH → LAW

Trace complete paths, mark nodes, identify branches, then select the series or parallel law.

Examiner habit: circuits are often redrawn into unfamiliar shapes. If the node connections are unchanged, the physics is unchanged.
Shape trap: components drawn side by side are not automatically parallel. They must connect to the same two nodes.
Quick Check · Can two components be parallel if one is drawn vertically and one horizontally?
Yes. Drawing orientation is irrelevant. They are parallel if both terminals of one component connect to the same two nodes as both terminals of the other.
2
Geometry first

Circuit symbols

cellbatteryd.c.power supplyGgeneratorswitchfixed resistor
Sources, control and resistance: learn the distinctive geometry, not just the label.
variable resistorHheaterNTC thermistorLDRlampMmotor
Control, sensors and output devices: connect each symbol to its action.
bellAammeterVvoltmetermagnetising coiltransformerfuse
Meters, magnetic components and protection symbols.
relaydiodeLED
A relay links two circuits; a diode is one-way; an LED is a light-emitting diode.
Which description identifies a diode?

Name

Identify the component from the symbol’s geometry.

Action

State what the component supplies, measures, senses, controls or transfers.

MnemonicSEE → NAME → ACT → USE

See the geometry, name the component, state its action, then connect that action to the circuit purpose.

Drawing technique: use a ruler for wires, leave clear junction dots where branches join, and draw recognised symbols—not sketches of real apparatus.
Cell/battery trap: one long–short pair is one cell. A battery contains two or more cells.
Quick Check · How do an ammeter and a voltmeter differ visually?
Both are circles; the ammeter contains A and the voltmeter contains V. Their circuit positions then reveal what they measure.
3
What each device does

Functions of circuit components

slider changesresistance changes
A variable resistor changes resistance and therefore changes current in a series circuit.
sensing circuitoutput circuitmagnetic link
A relay coil uses an electromagnet to operate contacts in a separate circuit.
AVseries meteracross component
An ammeter measures the component current; a voltmeter measures the p.d. between its terminals.
GroupComponentsPrecise action
sourcescell, battery, power supply, generatorsupply electrical energy / e.m.f.
controlswitch, fixed/variable resistoropen/close a path or set resistance/current
outputsheater, lamp, LED, motor, bell, coiltransfer electrical energy into thermal, light, kinetic, sound or magnetic effects
measurementammeter, voltmetermeasure current through or p.d. across
magnetic controlrelay, transformerswitch another circuit / transfer electrical energy between coils
protectionfusemelts and opens the circuit if current is excessive
  1. Name the component.
  2. State the physical quantity or effect it changes.
  3. Explain how that change affects the rest of the circuit.
  4. Use circuit-specific evidence: current path, p.d., resistance or magnetic action.
Relay wording: current in coil → magnetic field/electromagnet → armature moves → contacts open or close → separate output circuit changes.
Meter trap: an ammeter is not connected “near” the component; it must be in the same current path. A voltmeter is not in the path; it spans the component terminals.
Quick Check · Why can a relay use two different supplies?
The coil and contacts are linked magnetically/mechanically rather than by a conducting connection, so the sensing circuit can control a separate output circuit.
4
Translate the environment

LDRs, thermistors and diodes

temperature ↑resistance ↓
NTC thermistor: temperature increases, resistance decreases.
light intensity ↑resistance ↓
LDR: brighter light gives lower resistance; darkness gives higher resistance.
AdiodeBLEDCNTC thermistorDLDR
Diode and LED share the one-way base symbol; LED arrows point outwards to show emitted light.
voltage, Vcurrent, Idiode
A diode conducts strongly in the forward direction after a small forward p.d.; reverse current is almost zero.
ComponentCondition changeResistance/action
NTC thermistortemperature risesresistance falls
LDRlight intensity risesresistance falls
diodeforward connectionconducts readily; reverse connection blocks
LEDforward currentconducts and emits light
MnemonicNTC: HOT → LOW R · LDR: LIGHT → LOW R

Both sensor resistances fall for the named increase; the divider output still depends on where the sensor is placed.

Full sensor answer: never stop at “resistance decreases”. Continue to the voltage share and then the output-device response.
LED trap: the two arrows beside the diode symbol show light leaving the device. They are not current arrows.
Quick Check · Does an NTC thermistor have zero resistance when hot?
No. Its resistance decreases as temperature rises, but it is not assumed to become exactly zero.
5
Draw what you mean

Building and measuring a circuit

AVseries meteracross component
Correct resistance-measurement arrangement: A in series and V across the resistor.
A closed switch is a conducting link; an open switch breaks only the paths that use it.
A closed wire route around a lamp bypasses it; the bypass can also create a dangerously low total resistance if placed across a source.
How should you decide whether a lamp lights?
  1. Keep the source switched off while wiring.
  2. Build the main series path first.
  3. Add parallel branches and the voltmeter last.
  4. Check that no wire or ammeter directly bridges the source.
  5. Select a safe meter range, switch on briefly, read, then switch off before changing.

Ammeter

Very low resistance; place in series. Never bridge a source.

Voltmeter

Very high resistance; place across the selected component.

Safe practical: use a low-voltage current-limited supply; switch off before rewiring; avoid short circuits; stop if a wire, lamp or resistor becomes hot; keep liquids away from connections.
Diagram marks: complete loop, correct symbols, straight wires, visible junctions, correct meter positions and unambiguous source polarity.
Quick Check · Why is “connect the voltmeter near the lamp” insufficient?
“Near” gives no electrical relationship. The voltmeter must connect to the two lamp terminals so it measures their potential difference.
6
One path · one current

Series circuits

  • Series components carry the same current because charge has one path.
4 Ω6 Ωlamp0.6 A9 V2.4 V3.6 V3 V
Same current everywhere; the three component p.d.s add to the 9.0 V source.
AAvariable RL
The ammeter and components are in the same path, so all carry the same current.
SERIES LAWScurrentI₁ = I₂ = I₃p.d.Vsource = V₁ + V₂ + ...resistanceRT = R₁ + R₂ + ...same currentlarger R → larger V
Read every value and unit before selecting an equation.
Interactive · Series solver

Common current and voltage shares

RT = 12.0 Ω · I = 1.00 A · V₁ = 4.00 V · V₂ = 8.00 V
$I_1=I_2=...$   |   $V_{source}=V_1+V_2+...$   |   $R_T=R_1+R_2+...$
  1. Add series resistances.
  2. Find the one loop current if needed.
  3. Use the same current for every component.
  4. Find each p.d. from $V=IR$.
  5. Check that component p.d.s add to the source.
MnemonicSERIES SHARES CURRENT

One path cannot split the charge flow. The p.d. is shared according to resistance.

Used-up current trap: current is not consumed by the first component. Energy is transferred; the same charge flow continues through the loop.
Quick Check · Two series resistors are 2 Ω and 6 Ω. Which gets more p.d.?
The 6 Ω resistor. The current is the same, so $V=IR$ makes its p.d. three times the p.d. across the 2 Ω resistor.
7
Same two nodes · same p.d.

Parallel circuits

  • Parallel lamps receive supply voltage and can be independently switched; a broken branch need not stop others.
  • Follow wires around corners to recognise electrically identical arrangements drawn differently.
  • Parallel branches connect to the same pair of nodes and share p.d.
  • Current splits and recombines at junctions; conservation of charge makes total current in equal total current out.
branch P0.35 Abranch Q0.45 Abranch R0.4 A9 V1.2 A
Every branch has 9.0 V; the branch currents add to the 1.20 A source current.
1.20 A0.35 A0.45 AIjunction J
Current conservation gives I = 0.40 A.
8 Ω12 Ω6 V
Parallel branches share p.d., but their currents need not be equal when resistances differ.
Interactive · Junction accountant

Current in = current out

third branch = 0.40 A
$\sum I_{in}=\sum I_{out}$   |   $V_1=V_2=V_{supply}$ for parallel branches
  1. Mark the two common nodes.
  2. Label every current arrow at the junction.
  3. Add currents entering and add currents leaving.
  4. Use the same p.d. for each complete parallel branch.
  5. Check no branch current is larger than the source current in a simple split.
MnemonicPARALLEL SHARES VOLTAGE

Same two node potentials mean the same potential difference.

Explanation mark: current conservation follows because charge does not accumulate at an ordinary junction in steady operation.
Quick Check · Can two parallel branches have different currents?
Yes. They have the same p.d., but different branch resistances give different currents.

Pause · explain it yourself

Branches take 0.30 and 0.45 A. Find shared supply current.

Two resistors are connected in parallel across an ideal supply. Which quantity is the same across them?

8
Polarity decides add or subtract

Cells in series

  • Cells in series add e.m.f. when aligned and subtract when opposing.
1.5 V1.5 V1.5 Vcombined e.m.f. = 4.5 V
Three cells oriented the same way are aiding: their e.m.f.s add.
6 V1.5 V opposingcombined e.m.f. = 4.5 V
Opposing sources subtract: 6.0 V − 1.5 V = 4.5 V.
cellbatteryd.c.power supplyGgenerator
Sources may look different, but each supplies an e.m.f. to a complete circuit.
Interactive · Source-polarity decoder

Aiding or opposing?

combined e.m.f. = 4.50 V
  1. Mark the long line of each cell as positive.
  2. Follow one direction around the circuit.
  3. Add an e.m.f. when crossing a source from negative to positive.
  4. Subtract when a source opposes the others.
  5. State the final magnitude and unit.
Counting trap: two cells do not always give twice one cell’s e.m.f. A reversed cell opposes.
Diagram evidence: show every cell polarity clearly. If polarity is ambiguous, the numerical method cannot be credited reliably.
Quick Check · What is the result of two identical cells connected directly in opposition?
Their e.m.f.s cancel, giving combined e.m.f. 0 V in the ideal model.
9
Reduce → solve → expand

Equivalent resistance

  • Series resistances add.
  • Parallel resistances provide extra conducting paths, lowering total resistance below either branch resistance.
  • For two resistors, use 1/R = 1/R₁ + 1/R₂ or R = R₁R₂/(R₁ + R₂).
  • In a mixed circuit, first identify a pair sharing both endpoints, replace it with its equivalent and then combine genuine series elements.
  • Keep the assumed supply voltage explicit when calculating total current.
  • Check that the equivalent resistance is physically sensible before calculating further quantities.
  • A supply does not send a fixed current regardless of resistance.
  • With fixed supply voltage, changing equivalent resistance changes current.
4 Ω6 Ω6 Ωtotal R = 7 Ω
Reduce the 6 Ω parallel pair to 3 Ω, then add the 4 Ω series resistor.
6 Ω3 Ωtotal R = 2 Ω
Two-resistor shortcut: product divided by sum gives 2 Ω.
R₁R₂
Parallel resistors share p.d.; total current is the sum of branch currents.
Interactive · Parallel resistance

Product ÷ sum with a bound check

Rp = 2.00 Ω · below the smaller branch: yes
series: $R_T=R_1+R_2+...$
two in parallel: $1/R_T=1/R_1+1/R_2$ or $R_T=R_1R_2/(R_1+R_2)$
ArrangementCalculationMandatory bound
seriesadd directlytotal exceeds every member
parallelreciprocal / product-over-sumtotal is below the smallest branch
mixedreduce one clear block at a timecheck each reduced block and final topology
  1. Redraw the network into obvious blocks.
  2. Reduce one innermost series or parallel block.
  3. Replace it with its equivalent resistance.
  4. Repeat until one total remains.
  5. Solve source quantities, then expand back to branch quantities.
MnemonicREDUCE → SOLVE → EXPAND → CHECK

Do not mix branch currents with source current while the topology is still hidden.

Parallel average trap: the equivalent resistance is not between the two values. It must be smaller than both.
Quick Check · Why does adding a parallel branch reduce total resistance?
The new branch provides an additional route for charge. More total current flows for the same p.d., so $R_T=V/I_T$ is smaller.

Pause · explain it yourself

Why is two-resistor parallel resistance below either resistor alone?

Your turn · Two series resistors have resistances 12 Ω and 18 Ω. Find total resistance.

Decimals and scientific notation are accepted. Compatible units are accepted.

10
Brightness follows operating conditions

Lamps in parallel

0.25 A0.25 A0.25 A6 V0.75 A
Three identical parallel lamps: each has 6.0 V and the source current is 0.75 A.
6 V
Opening one branch switch turns off only that lamp; the other branch remains complete.
lamp Plamp Q6 V
Series lamps share the supply p.d.; one open lamp breaks the only path.

Parallel advantages

Each lamp receives the supply p.d.; each can have its own switch; failure/opening of one branch leaves the others working.

Series limitations

Lamps share p.d.; adding lamps increases total resistance; one open component breaks the whole path.

  1. Decide whether lamps are identical.
  2. Identify the p.d. across each lamp.
  3. If needed, compare current or power at the operating point.
  4. Only then compare brightness.
MnemonicBRIGHTNESS AFTER VOLTAGE

Do not rank lamps from their drawn position. Establish the electrical operating conditions first.

Parallel explanation: “both lamps are connected across the same two supply nodes, so both receive the full supply p.d.”
Identical-current trap: parallel lamps have the same p.d., not automatically the same current. Equal current additionally requires identical operating behaviour.
Quick Check · What changes at the source when another parallel lamp is added?
The combined resistance decreases and the source current increases. Existing ideal-source branch p.d.s remain unchanged.
11
Voltage follows resistance share

Potential dividers

  • A series pair divides voltage in proportion to resistance because both resistors carry the same current.
  • For an unloaded divider, Vout = Vsupply × Rout/(Rtop + Rbottom), where Rout names the resistor across which output is measured.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminals12 V+−2.0 kΩ4.0 kΩVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
Output across the lower 4.0 kΩ resistor is 8.0 V.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminalsVs+−R₁R₂VoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
For output across R₂: Vout/Vs = R₂/(R₁+R₂).
Potential divider · output measured between open terminalsPotential divider · output measured between open terminals6 V+−sliderVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
A variable divider uses a sliding contact to select a fraction of the track and supply p.d.
Interactive · Divider calculator

Choose the output component

Vout = 8.00 V · other p.d. = 4.00 V
$R_1/R_2=V_1/V_2$
across R₂: $V_{out}=V_s×R_2/(R_1+R_2)$
  1. Circle the two output terminals.
  2. Identify which resistance lies between them.
  3. Add the two series resistances.
  4. Multiply the supply by output resistance / total resistance.
  5. Check that output lies between 0 V and the supply p.d.
MnemonicVOLTAGE FOLLOWS THE RESISTOR YOU MEASURE

The output share increases when the resistance between the output terminals becomes a larger fraction of the total.

Numerator trap: do not automatically put the lower resistor in the numerator. Put the resistor actually spanned by the output terminals.
Quick Check · Two equal divider resistors are across 10 V. What output across either one?
5.0 V. Equal resistances carry the same current and share the supply p.d. equally.
12
Condition → R → Vout → response

Sensor potential dividers

  • If output is across a lower sensor, falling sensor resistance lowers output voltage.
  • Measuring across the other resistor reverses that trend.
  • A connected load can change the division, so the simple expression assumes negligible loading.
  • Name output terminals rather than memorising that a sensor always raises or lowers voltage.
  • An NTC thermistor’s resistance decreases as temperature rises; an LDR’s decreases in brighter light.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminals6 V+−LDRfixed RVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
Brighter light lowers the upper LDR resistance, so output across the fixed lower resistor rises.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminals6 V+−fixed RNTCVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
Higher temperature lowers the lower NTC resistance, so output across the NTC falls.
sensing circuitoutput circuitmagnetic link
The divider can feed a relay stage; the relay then controls a separate warning circuit.
temperaturechangesVout changes
The component response must be connected to the divider ratio before predicting the output.
Sensor position / outputNamed condition risesOutput change
LDR lower; output across LDRlight rises → LDR R fallsoutput falls
LDR upper; output across fixed lower Rlight rises → upper R fallsoutput rises
NTC lower; output across NTCtemperature rises → NTC R fallsoutput falls
NTC upper; output across fixed lower Rtemperature rises → upper R fallsoutput rises
  1. Name the environmental change.
  2. State the sensor-resistance change.
  3. Locate the output terminals.
  4. Decide whether the output resistance is a larger or smaller fraction of the total.
  5. State output p.d. change.
  6. State the relay, bell, lamp, motor or LED response.
Exam chainCONDITION → SENSOR R → SHARE → VOUT → DEVICE

Five linked arrows turn a one-mark fact into a complete explanation.

Reverse the response: swap the sensor and fixed resistor, or measure output across the other component. Always redraw and re-trace the output terminals.
Sensor-only trap: “LDR resistance decreases” does not decide whether output rises or falls until output placement is known.
Quick Check · NTC on top, output across fixed lower resistor. What happens when temperature rises?
NTC resistance falls, the fixed lower resistor becomes a larger fraction of the total, so output p.d. rises.

Pause · explain it yourself

An LDR forms the lower resistor with output across it. What does brighter light do?

13
Alternative to Practical

ATP Lab Lens · Build safely, record paired evidence, process and evaluate

d.c.0.35 A0.45 A0.8 AA before split · A in each branch
Junction method: compare the main current with the sum of both branch currents.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminals6 V+−LDRfixed RVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
Sensor-divider method: vary one environmental quantity and measure output p.d.
AVseries meteracross componentsame temperature · paired readings
Resistance method: measure current through and p.d. across the selected component at the same condition.
Apparatus

Current-limited low-voltage supply, switch, standard components, secure leads, correct-range meters and a controlled sensor stimulus.

Variables

Name independent, dependent and all controls that affect supply, geometry, temperature, light or contacts.

Evidence

Use repeats, means, calculated sums/ratios and a graph with both quantity names and units.

InvestigationIndependentDependentCritical controls
junction rulesupply setting / branch resistancemain and branch currentssame setting, resistors, temperature, meters
slider dividerslider positionoutput p.d.supply, track, contact method
LDR dividerlight intensity / proxyoutput p.d.ambient light, supply, geometry, temperature
NTC dividertemperatureoutput p.d.equilibrium, stirring, supply, fixed resistor
Linked evaluation: “The LDR also warms, changing its resistance independently of light; use a cool LED source, keep exposure brief and monitor temperature.” Limitation → physical effect → improvement.
Safe practical: low voltage and current limiting; switch off before rewiring; no ammeter across the supply; prevent short circuits; keep liquid-bath electrical contacts dry; avoid hot water and hot components.
Quick Check · Why is one reading at one sensor condition weak evidence?
It cannot show a trend or expose random variation. Use several well-spaced conditions, repeat each reading and compare means.
14
One-page examiner logic

Master Electric Circuits by keeping topology, conservation, reduction and response in order

one pathsame two nodes
First decide one path or same two nodes.
R₁R₂IVs
Series ledger: one current; p.d.s and resistances add.
R₁R₂Vs
Parallel ledger: one p.d.; branch currents add.
Potential divider · output measured between open terminalsPotential divider · output measured between open terminalsVs+−LDRfixed RVoutUse a high-resistance voltmeter across the terminals; do not join them with a wire.
Response ledger: condition → sensor R → divider share → output.

1 · Read

Name symbols, mark source polarity, close/open switches and trace complete paths.

2 · Classify

One path means series; same two nodes means parallel.

3 · Conserve

Current in = current out; series p.d.s add; parallel branches share p.d.

4 · Calculate

Reduce → solve → expand; enforce resistance and voltage bounds.

series: $I$ same · $V_s=\sum V$ · $R_T=\sum R$
parallel: $V$ same · $\sum I_{in}=\sum I_{out}$ · $1/R_T=\sum(1/R)$
divider: $V_{out}=V_s×R_{out}/R_T$
Final chainSYMBOL → PATH → NODE → LAW → REDUCE → SOLVE → CHECK

For a sensor, append: condition → resistance → output p.d. → device response.

Final check · What four tests catch most circuit mistakes?
Check topology from nodes; check junction current conservation; check p.d. totals/sharing; check resistance bounds and whether the result behaves sensibly when a branch is opened or added.
Interactive mastery: 0 / 8 explored

Explore all eight checkpoints, then move to the independent Practice and Exam Arena banks.